Toyota Tundra. Manual — part 2488
Fig. 59: Identifying Headlight Connector Terminals - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. Measure the voltage according to the value(s) in the table below.
Standard voltage
HEADLIGHT LOW BULB - BATTERY LH
b. for RH:
1. Disconnect the A11 headlight connector.
Fig. 60: Identifying Headlight Connector Terminals - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. Measure the voltage according to the value(s) in the table below.
Standard voltage
HEADLIGHT LOW BULB - BATTERY RH
Tester Connection
Switch Condition
Specified
Condition
A10-2 - Body
ground
Light control switch HEAD, dimmer switch Low
11 to 14 V
Light control switch HEAD, dimmer switch except
Low
Below 1 V
Tester Connection
Switch Condition
Specified
Condition
A11-2 - Body
ground
Light control switch HEAD, dimmer switch Low
11 to 14 V
Light control switch HEAD, dimmer switch except
Low
Below 1 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
NG: Go to step 4
OK: REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT LOW BULB - BODY
GROUND)
4. INSPECT HEADLIGHT RELAY (HEAD)
a. Remove the headlight relay from the engine room relay block.
Fig. 61: Identifying Headlight Relay (Head) Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
HEADLIGHT RELAY (HEAD)
NG: REPLACE HEADLIGHT RELAY
OK: Go to next step
5. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - BATTERY)
a. Remove the headlight relay from the engine room relay block.
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals land 2 10 kohms or higher
When battery voltage is applied to terminals 1 and 2
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Fig. 62: Identifying Headlight Relay (Head) Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
HEADLIGHT RELAY - BATTERY
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
6. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - HEADLIGHT LOW BULB)
Fig. 63: Identifying Headlight Relay (Head) And Headlight Connector Terminals
Tester Connection
Condition Specified Condition
Headlight relay terminal 1 - Body ground
Always
11 to 14 V
Headlight relay terminal 3 - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Remove the headlight relay from the engine room relay block.
b. for LH:
1. Disconnect the A10 headlight connector.
2. Measure the resistance according to the value(s) in the table below.
Standard resistance
HEADLIGHT RELAY - HEADLIGHT LOW BULB LH
c. for RH:
1. Disconnect the A11 headlight connector.
2. Measure the resistance according to the value(s) in the table below.
Standard resistance
HEADLIGHT RELAY - HEADLIGHT LOW BULB RH
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
7. CHECK HEADLIGHT (LOW BEAM)
a. Disconnect the DB ECU connector.
Tester Connection
Condition Specified Condition
Headlight relay terminal 5 - A10-2
Always
Below 1 ohms
Headlight relay terminal 5 - Body ground Always
10 kohms or higher
Tester Connection
Condition Specified Condition
Headlight relay terminal 5 - A11-2
Always
Below 1 ohms
Headlight relay terminal 5 - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст