Toyota Tundra. Manual — part 2248

illustration.

Torque: for stud bolt A

5.0 N*m (51 kgf*cm, 44 in.*lbf)

for stud bolt B

9.0 N*m (92 kgf*cm, 80 in.*lbf)

Fig. 328: Identifying Oil Pan Stud Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2. INSTALL RING PIN

a. Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.

Standard protrusion

STANDARD PROTRUSION SPECIFICATION

Item

Ring Pin Diameter

Specified Condition

Ring pin A 13 mm (0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)

Ring pin B 11 mm (0.433 in.) 3.6 to 4.6 mm (0.142 to 0.181 in.)

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

Fig. 329: Locating Ring Pin
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

3. INSTALL REAR CRANKSHAFT OIL SEAL

a. Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.

SST 09223-15030, 09950-70010 (09951 -07100)

Standard depth:

0 to 1.0 mm (0 to 0.0394 in.)

4. INSTALL OIL DRAIN PIPE SUB-ASSEMBLY

a. Apply a light coat of engine oil to a new O-ring.

NOTE:



Keep the lip free from foreign matter.



Do not tap on the oil seal at an angle.

Fig. 330: Tapping In Oil Seal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

b. Install the O-ring to the drain pipe.

c. Install the oil drain pipe with the bolt.

Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)

Fig. 331: Locating Oil Drain Pipe With Mounting Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

5. INSTALL ENGINE REAR OIL SEAL RETAINER

a. Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three

Bond 1207B or equivalent

Seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)

Application position from inside edge of retainer:

3.5 mm (0.138 in.)

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

Fig. 332: Identifying Seal Packing Areas On Engine Rear Oil Seal Retainer
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Install the oil seal retainer with the 6 bolts.

Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTE:



Remove any oil from the contact surface.



Install the engine rear oil seal retainer within 3 minutes and
tighten the bolts and nuts within 15 minutes after applying seal
packing.

NOTE:



Do not start the engine for at least 2 hours after installing.



When installing the oil seal retainer, make sure the lip of the oil
seal is not damaged.



When installing the oil seal retainer, make sure the lip of the oil
seal is not folded incorrectly.

Fig. 333: Locating Oil Seal Retainer With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra