Toyota Tundra. Manual — part 2221
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1. INSTALL FRONT CRANKSHAFT OIL SEAL
a. Apply MP grease to the lip of a new oil seal.
b. Using SST and a hammer, tap in the oil seal to a depth between 0 to 1.0 mm (0 to 0.0394 in.) from
the timing chain cover edge.
SST 09223-22010,09506-35010
2. INSTALL CRANKSHAFT TIMING GEAR KEY
a. Install the crankshaft timing gear key.
NOTE:
Keep the lip free from foreign matter.
Do not tap the oil seal at an angle.
Fig. 162: Installing Front Crankshaft Oil Seal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 163: Identifying Crankshaft Timing Gear Key
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. INSTALL CRANKSHAFT PULLEY (See INSTALLATION )
4. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY (w/ Oil Cooler) (See INSTALLATION )
5. INSTALL NO. 1 OIL COOLER BRACKET (w/ Oil Cooler) (See INSTALLATION )
6. CONNECT NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)
a. Connect the 2 water by-pass hoses to the oil cooler.
Fig. 164: Locating No. 2 Water By-Pass Pipe Sub-Assembly Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Install the 3 by-pass pipe bolts.
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
7. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY (w/ o Oil Cooler) (See INSTALLATION )
8. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY (See INSTALLATION )
9. CONNECT FRONT STABILIZER BAR
a. Connect the stabilizer bar and install the 2 stabilizer bushes and 2 stabilizer brackets with the 4
bolts.
Torque: 69 N*m (704 kgf*cm, 51 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 165: Locating Front Stabilizer Bar Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
10. INSTALL FAN SHROUD (See INSTALLATION )
11. INSTALL FAN AND GENERATOR V BELT (See INSTALLATION )
12. INSTALL INLET RADIATOR HOSE
13. ADD ENGINE COOLANT (See COOLANT )
14. INSPECT FOR COOLANT LEAK (See COOLING SYSTEM )
15. INSPECT FOR OIL LEAK (See REPLACEMENT )
16. CHECK ENGINE OIL LEVEL (See LUBRICATION SYSTEM )
17. INSTALL NO. 1 ENGINE UNDER COVER (See REPLACEMENT )
18. INSTALL V-BANK COVER SUB-ASSEMBLY (See INSTALLATION )
REAR CRANKSHAFT OIL SEAL
COMPONENTS
Fig. 166: Identifying Rear Crankshaft Oil Seal With Torque Specifications
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
a. Remove the automatic transmission (See REMOVAL ).
2. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (See REMOVAL )
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
3. REMOVE REAR CRANKSHAFT OIL SEAL
a. Using a knife, cut off the lip of the oil seal.
b. Using a screwdriver, pry out the oil seal.
HINT:
Tape the screwdriver tip before use.
Fig. 167: Prying Out Oil Seal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1. INSTALL REAR CRANKSHAFT OIL SEAL
a. Apply MP grease to the lip of a new oil seal.
b. Using SST and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer
edge.
SST 09223-56010
NOTE:
Do not damage the surface of the oil seal press fit hole and
crankshaft.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст