Toyota Tundra. Manual — part 919
Fig. 29: Identifying ABS Warning And Brake Warning Lights
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
DTC CHECK/CLEAR
1. DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE)
a. Check DTC.
1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
SST 09843-18040
Trouble Area
Reference
ABS warning light circuit
ABS WARNING LIGHT REMAINS ON
BRAKE warning light circuit
BRAKE WARNING LIGHT REMAINS ON
VSC OFF indicator light circuit
VSC OFF INDICATOR LIGHT REMAINS
ON
SLIP indicator light circuit
SLIP INDICATOR LIGHT REMAINS ON
AUTO LSD indicator light circuit
AUTO LSD INDICATOR LIGHT REMAINS
ON
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
2. Turn the ignition switch to ON.
Fig. 30: Identifying DLC3 Connector Terminal TC And CG
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. Read the DTC from the ABS warning light and VSC OFF indicator light on the combination
meter.
HINT:
If no code appears, inspect the TC and CG terminal circuit, and the ABS warning light and
VSC OFF indicator light circuits.
TROUBLE AREA PROCEDURE TABLE
Trouble Area
Reference
TC and CG terminal circuit
TC AND CG TERMINAL CIRCUIT
ABS warning light circuit
ABS WARNING LIGHT REMAINS ON or
ABS WARNING LIGHT DOES NOT
COME ON
VSC OFF indicator light circuit
VSC OFF INDICATOR LIGHT
REMAINS ON or VSC OFF INDICATOR
LIGHT DOES NOT COME ON
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
Fig. 31: Identifying ABS Warning Light And VSC Off Indicator Light
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4. As examples, refer to the table below for the blinking patterns of the normal system code and
trouble codes 11 and 21.
Fig. 32: Examples Of Normal System Code And Trouble Codes 11 And 21 Blinking
Pattern
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5. Codes are explained in the code table (see DIAGNOSTIC TROUBLE CODE TABLE ).
6. After completing the check, disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
order.
b. Clear DTC.
1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
SST 09843-18040
Fig. 33: Identifying DLC3 Connector Terminal TC And CG
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. Turn the ignition switch to ON.
3. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5
seconds.
4. Check that the warning light indicates a normal system code.
5. Remove SST from the terminals of the DLC3.
HINT:
Clearing the DTCs cannot be performed by removing the battery cable or the ECU-IG fuse.
Fig. 34: Depressing Brake Pedal For Checking Warning Light
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. DTC CHECK/CLEAR (WHEN USING TECHSTREAM)
a. Check DTC.
1. Connect the Techstream to the DLC3.
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст