Toyota Tundra. Manual — part 576
Fig. 419: Identifying O1, O2, O7 And O8 Speaker Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE REAR NO. 2 SPEAKER (See REMOVAL )
16. INSPECT BOX SPEAKER
a. Disconnect the P14 speaker connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
BOX SPEAKER TESTER CONNECTION SPECIFIED CONDITION
Tester Connection Condition Specified Condition
1 - 2
Always
1.5 to 2.1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 420: Identifying P14 Speaker Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE BOX SPEAKER (See REMOVAL )
OK: Go to Next Step
17. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - BOX
SPEAKER)
a. Disconnect the K17 amplifier connector.
b. Disconnect the P14 speaker connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - BOX SPEAKER)
TESTER CONNECTION SPECIFIED CONDITION
Fig. 421: Identifying K17 Amplifier Connector And P14 Speaker Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Tester Connection
Condition Specified Condition
K17-5 (WF1+) - P14-1
Always
Below 1 ohms
K17-12 (WF1-) - P14-2
K17-5 (WF1+) - Body ground
Always
10 kohms or higher
K17-12 (WF1-) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE STEREO COMPONENT AMPLIFIER (See REMOVAL )
SOUND SIGNAL CIRCUIT BETWEEN NAVIGATION RECEIVER ASSEMBLY AND STEREO
JACK ADAPTER
DESCRIPTION
The stereo jack adapter sends an external device sound signal to the navigation receiver through this circuit. The
sound signal that has been sent is amplified by stereo component amplifier, and then is sent to speakers.
If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no
malfunction in the stereo component amplifier, navigation receiver, or speakers.
WIRING DIAGRAM
Fig. 422: Sound Signal Circuit Between Navigation Receiver Assembly And Stereo Jack Adapter -
Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (NAVIGATION ADAPTER) RECEIVER - STEREO
JACK
a. Disconnect the K5 receiver connector.
b. Disconnect the J7 adapter connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
HARNESS AND CONNECTOR (NAVIGATION ADAPTER) RECEIVER - STEREO JACK
TESTER CONNECTION SPECIFIED CONDITION
Fig. 423: Identifying K5 Receiver Connector And J7 Adapter Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
AVC-LAN CIRCUIT
DESCRIPTION
Tester Connection
Condition Specified Condition
K5-3 (VAL+) - J7-1 (ALO)
Always
Below 1 ohms
K5-2 (VAR+) - J7-2 (ARO)
K5-5 (VA-) - J7-3 (ASGN)
K5-5 (VA-) - J7-5 (AUXG)
K5-6 (ADPG) - J7-4 (AUXO)
K5-3 (VAL+) - Body ground
Always
10 kohms or higher
K5-2 (VAR+) - Body ground
K5-5 (VA-) - Body ground
K5-6 (ADPG) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст