Toyota Tundra. Manual — part 736
Install the courtesy light assembly (see REASSEMBLY ).
10. INSTALL REAR DOOR FRAME GARNISH LH
a. for Double Cab:
Install the rear door frame garnish LH (See REASSEMBLY ).
b. for CrewMax:
Install the rear door frame garnish LH (see REASSEMBLY ).
11. INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH
a. for Double Cab:
Install the rear upper door armrest base panel LH (See REASSEMBLY ).
b. for CrewMax:
Install the rear upper door armrest base panel LH (see REASSEMBLY ).
12. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH
a. for Double Cab:
Install the rear door inside handle bezel plug LH (See REASSEMBLY ).
b. for CrewMax:
Install the rear door inside handle bezel plug LH (see REASSEMBLY ).
13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
BACK POWER WINDOW SWITCH
COMPONENTS
NOTE:
Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 79: Identifying Back Power Window Switch Components
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1. REMOVE FRONT DOOR SCUFF PLATE LH (See REMOVAL )
2. REMOVE COWL SIDE TRIM BOARD LH (See REMOVAL )
3. REMOVE INSTRUMENT SIDE PANEL LH (See REMOVAL )
4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH (See
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
REMOVAL )
5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Back Window)
a. Using a screwdriver, detach the 2 claws.
Fig. 80: Identifying Power Window Regulator Switch Assembly Claws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Tape the screwdriver tip before use.
b. Remove the regulator switch.
INSPECTION
1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Back Window)
a. Check the resistance.
1. Measure the resistance according to the value(s) in the table below.
Standard Resistance
POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR BACK WINDOW)
Tester Connection
Switch Condition Specified Condition
Connector A-3 (UP) - Connector A-4 (E)
UP
Pressed
Below 1 ohms
Not pressed 10 kohms or higher
Connector A-2 (DN) - Connector A-4 (E) DOWN
Pressed
Below 1 ohms
Not pressed 10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 81: Identifying Power Window Regulator Switch Assembly (For Back Window)
Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
If the result is not as specified, replace the power window regulator switch assembly.
b. Check that the LED illuminates.
1. Apply battery voltage to the power window regulator switch and check that the LED
illuminates.
OK
POWER WINDOW REGULATOR SWITCH AND LED ILLUMINATES
If the result is not as specified, replace the power window regulator switch assembly.
INSTALLATION
1. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Back Window)
a. Attach the 2 claws to install the regulator switch.
Measurement Condition
Specified Condition
Battery positive (+) --> Connector A-S (ILL+)
Battery negative (-) --> Connector A-1 (ILL-)
LED illuminates
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст