Toyota Tundra. Manual — part 2472
Fig. 11: Lighting System Diagram (3 Of 3)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Communication table
COMMUNICATION CHART
Sender
Receiver
Signal
Line
ECM
Main Body ECU
Vehicle speed signal
CAN
Headlight Lo beam signal
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
SYSTEM DESCRIPTION
1. ILLUMINATED ENTRY SYSTEM
a. When the doors are unlocked by a key or door control transmitter operation, or when a door is
opened or closed, the illuminated entry system turns on the room light, map light, foot light and
ignition key cylinder light.
1. The main body ECU receives the following signals (A).
Door control switch signal
Door detection switch signal
Ignition switch signal
2. The main body ECU controls the following signal based on the signals listed in A.
Illumination operation signal
3. The main body ECU controls the on/off and fade-in/fade-out operation of the following parts.
Room light
Map light
Foot light
Ignition key cylinder light
2. BATTERY SAVE SYSTEM
a. When the ignition switch is turned OFF and any of the doors is open continuously for 20 minutes,
the main body ECU turns the illumination operation signal off. As a result, the room light, map
light, foot light and ignition key cylinder light turn off.
1. The main body ECU receives the following signals (B).
Door courtesy light switch signal
Ignition switch signal
2. The main body ECU controls the following signal based on the signal listed in B (C).
Illumination operation signal
3. The main body ECU controls the illumination period of the following parts based on the
signal listed in C.
Room light
Map light
Foot light
Ignition key cylinder light
Main Body ECU
Combination Meter
Headlight Hi beam signal
Taillight signal
Front door courtesy light switch LH signal
Front door courtesy light switch RH signal
Rear door courtesy light switch LH signal
Rear door courtesy light switch RH signal
CAN
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Cargo light
3. MANUAL LIGHT CONTROL SYSTEM
a. This system functions when lights such as the headlight, taillight and front fog light are illuminated
by manual operation of the light control switch.
1. The main body ECU receives the following signals (D).
Light control switch signal
Headlight dimmer switch signal
Front fog light switch signal
2. The main body ECU controls the following signals based on the signals listed in D (E).
Headlight relay operation signal
Taillight relay operation signal
Front fog light relay operation signal
3. The main body ECU controls the on/off operation of the following parts based on the signal
listed in E.
Headlight (Low)
Headlight (High)
Front fog light
4. LIGHT AUTO TURN OFF SYSTEM
a. When the headlight and taillight are both illuminated by the operation of the light control switch, if
the ignition switch is turned OFF, this system continues illuminating the headlight and taillight for
approximately 30 seconds, and then turns them off. However, when all the doors are locked using
the door control switch, key or transmitter OFF switch within 30 seconds, this system turns the
headlight and taillight off immediately. Also, when only the taillight is illuminated by the operation
of the light control switch, if the ignition switch is turned OFF and the driver door is opened, this
system turns the taillight off immediately.
1. The main body ECU receives the following signals (F).
Door courtesy light switch signal
Ignition switch signal
2. The main body ECU controls the following signals based on the signals listed in F (G).
Headlight relay operation signal
Taillight relay operation signal
Daytime running light relay operation signal
3. The main body ECU controls the on/off operation of the following parts based on the signal
listed in G.
Headlight (Low)
Headlight (High)
Taillight
5. DAYTIME RUNNING LIGHT SYSTEM
a. This system is directly connected to the turn signal light and is designed to automatically activate
the daytime running lights in order to increase the visibility of the vehicle.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
1. The main body ECU receives the following (H).
Ignition switch signal
Engine speed signal
Parking brake switch signal
Light control switch signal
2. The main body ECU and turn signal flasher controls the following signal based on the signals
listed in H (I).
Daytime running light relay operation signal
3. The main body ECU and turn signal flasher controls the on/off operation of the following
part based on the signal listed in I.
Turn signal light
HOW TO PROCEED WITH TROUBLESHOOTING
HINT:
Use these procedures to troubleshoot the lighting system.
*: Use the Techstream.
1. VEHICLE BROUGHT TO WORKSHOP
2. INSPECT BATTERY VOLTAGE
Standard voltage:
11 to 14 V
If the voltage is below 11V, recharge or replace the battery before proceeding.
3. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a. Use Techstream to check if the CAN communication system is functioning normally.
Result
COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM
B: Go TO CAN COMMUNICATION SYSTEM
A: Go to next step
4. CHECK FOR DTC*
Result
Proceed to
CAN DTC is not output
A
CAN DTC is output
B
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст