Toyota Tundra. Manual — part 442
b. Techstream
Main body
MAIN BODY TECHSTREAM DATA LIST
OK: On tester screen, each item changes between ON and OFF according to above chart.
NG: Go to step 5
OK: Go to Next Step
3. INSPECT OUTER REAR VIEW MIRROR LH
a. Remove the mirror LH (see REMOVAL ).
b. Apply battery voltage and check the operation of the power mirror.
OK
OUTER REAR VIEW MIRROR LH MEASUREMENT CONDITION SPECIFIED
CONDITION CHART
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic
Note
Mirror selection
SW (Left)
Mirror master switch signal for
LH mirror / ON or OFF
ON: Switch is in L position
OFF: Switch is OFF or in R
position
-
Mirror position
SW (Right)
Mirror control switch signal
(RIGHT) / ON or OFF
ON: RIGHT switch is ON
OFF: Any switch except RIGHT
is ON or all switches are OFF
-
Mirror position
SW (Left)
Mirror control switch signal
(LEFT) / ON or OFF
ON: LEFT switch is ON
OFF: Any switch except LEFT is
ON or all switches are OFF
-
Mirror position
SW (UP)
Mirror control switch signal
(UP) / ON or OFF
ON: UP switch is ON
OFF: Any switch except UP is
ON or all switches are OFF
-
Mirror position
SW (Down)
Mirror control switch signal
(DOWN) / ON or OFF
ON: DOWN switch is ON
OFF: Any switch except DOWN
is ON or all switches are OFF
-
Measurement Condition
Specified Condition
Battery positive (+) --> Terminal 10 (MV)
Battery negative (-) --> Terminal 11 (M+)
Turns upward (A)
Battery negative (-) --> Terminal 10 (MV)
Battery positive (+) --> Terminal 11 (M+)
Turns downward (B)
Battery positive (+) --> Terminal 12 (MH)
Battery negative (-) --> Terminal 11 (M+)
Turns left (C)
Battery negative (-) --> Terminal 12 (MH)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Mirror - Tundra
Fig. 15: Inspecting Outer Rear View Mirror LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE OUTER REAR VIEW MIRROR LH (see REMOVAL )
OK: Go to Next Step
4. CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - OUTER REAR
VIEW MIRROR LH)
a. Disconnect the N8 ECU connector.
b. Disconnect the N5 mirror connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - OUTER REAR
VIEW MIRROR LH) TESTER CONNECTION SPECIFIED CONDITION CHART
Battery positive (+) --> Terminal 11 (M+)
Turns right (D)
Tester Connection
Condition Specified Condition
N8-18 (M+L) - N5-11 (M+)
Always
Below 1 ohms
N8-19 (MHL) - N5-12 (MH)
N8-20 (MVL) - N5-10 (MV)
N5-11 (M+) - Body ground
Always
10 kohms or higher
N5-12 (MH) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Mirror - Tundra
Fig. 16: Identifying N8 ECU And N5 Mirror Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE OUTER MIRROR CONTROL ECU (See DISASSEMBLY )
5. INSPECT OUTER MIRROR SWITCH ASSEMBLY
a. Remove the switch (see REMOVAL ).
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
OUTER MIRROR SWITCH ASSEMBLY TESTER CONNECTION SPECIFIED
CONDITION CHART
N5-10 (MV) - Body ground
Tester Connection
Switch Condition
Specified Condition
3 (M+) - 2 (E)
UP switch pushed
100 ohms
DOWN switch pushed
470 ohms
LEFT switch pushed
800 ohms
RIGHT switch pushed
250 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Mirror - Tundra
Fig. 17: Inspecting Outer Mirror Switch Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE OUTER MIRROR SWITCH ASSEMBLY (see REMOVAL )
OK: Go to Next Step
6. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)
a. Disconnect the J4 ECU connector.
b. Disconnect the L6 switch connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)
TESTER CONNECTION SPECIFIED CONDITION CHART
1 (MSE) - 2 (E)
No switches pushed
10 kohms or higher
L switch pushed
100 ohms
Tester Connection
Condition Specified Condition
J4-2 (MIRE) - L6-2 (E)
Always
Below 1 ohms
J4-11 (MIRB) - L6-3 (M+)
Always
Below 1 ohms
J4-12 (MIRS) - L6-1 (MSW) Always
Below 1 ohms
L6-3 (M+) - Body ground
Always
10 kohms or higher
L6-2 (E) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Mirror - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст