Toyota Tundra. Manual — part 1166
RESULT CHART
HINT:
If there is an open circuit, the Techstream indicates 40°C (-40°F).
If there is a short circuit, the Techstream indicates 140°C (284°F) or higher.
B : Go to step 5
C : CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
A : Go to next step
3. READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
a. Disconnect the D8 Mass Air Flow (MAF) meter connector.
b. Connect terminals 4 (THA) and 5 (E2) of the MAF meter wire harness side connector.
c. Connect the Techstream to the DLC3.
d. Turn the ignition switch ON.
e. Turn the Techstream ON.
f. Enter the following menus: Powertrain/Engine and ECT/All Data/Intake Air.
g. Read the value displayed on the Techstream.
Standard value:
140°C (284°F) or higher
NG : Go to step 4
Temperature Displayed Proceed To
-40°C (-40°F)
A
140°C (284°F) or higher
B
Same as actual IAT
C
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Fig. 63: Disconnecting D8 Mass Air Flow (MAF) Meter Connector
OK : CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW
METER (See REMOVAL )
4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a. Disconnect the D8 MAF meter connector.
b. Disconnect the D74 ECM connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
D8-4 (THA) - D74-73 (THA) Always
Below 1 ohms
D8-5 (E2) - D74-98 (ETHA)
Always
Below 1 ohms
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Fig. 64: Identifying D8 MAF Meter Connector Terminals
OK : CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (See REMOVAL )
5. REAP VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
a. Disconnect the D8 MAF meter connector.
b. Connect the Techstream to the DLC3.
c. Turn the ignition switch ON (IG).
d. Turn the Techstream ON.
e. Enter the following menus: Powertrain/Engine and ECT/All Data/Intake Air.
f. Read the value displayed on the Techstream.
Standard value:
-40°C (-40°F)
NG : Go to step 6
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Fig. 65: Disconnecting D8 MAF Meter Connector
OK : REPLACE MASS AIR FLOW METER (See REMOVAL )
6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a. Disconnect the D8 MAF meter connector.
b. Disconnect the D74 ECM connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
D8-4 (THA) or D74-73 (THA) - Body ground Always
10 kohms or higher
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст