Toyota Tundra. Manual — part 599
Fig. 44: Indicator - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK FUSE (ECU-IG No. 1)
a. Remove the ECU-IG No. 1 fuse from the main body ECU.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FUSE (ECU-IG No. 1) RESISTANCE SPECIFICATION
NG: REPLACE FUSE
OK: Go to next step
2. CHECK HARNESS AND CONNECTOR (ACCESSORY METER - BATTERY)
a. Disconnect the K20 meter connector.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
HARNESS AND CONNECTOR (ACCESSORY METER - BATTERY) VOLTAGE
SPECIFICATION
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always
Below 1 ohms
Tester Connection
Switch Condition Specified Condition
K20-23 (IG) - Body ground Ignition switch ON
11 to 14 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Parking Assist/Monitoring - Tundra
Fig. 45: Identifying K20 Meter Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
3. CHECK HARNESS AND CONNECTOR (ACCESSORY METER - ECU)
a. Disconnect the J35 ECU connector.
b. Disconnect the K20 meter connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (ACCESSORY METER - ECU) RESISTANCE
SPECIFICATION
Tester Connection
Condition Specified Condition
J35-15 (L1) - K20-3 (RR)
Always
Below 1 ohms
J35-16 (L2) - K20-4 (FR)
Always
Below 1 ohms
J35-17 (L3) - K20-7 (RL)
Always
Below 1 ohms
J35-18 (L4) - K20-8 (FL)
Always
Below 1 ohms
J35-19 (L5) - K20-5 (BK)
Always
Below 1 ohms
J35-20 (L6) - K20-6 (OP)
Always
Below 1 ohms
J35-15 (L1) - Body ground Always
10 kohms or higher
J35-16 (L2) - Body ground Always
10 kohms or higher
J35-17 (L3) - Body ground Always
10 kohms or higher
J35-18 (L4) - Body ground Always
10 kohms or higher
J35-19 (L5) - Body ground Always
10 kohms or higher
J35-20 (L6) - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Parking Assist/Monitoring - Tundra
Fig. 46: Identifying J35 ECU And K20 Meter Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
4. REPLACE ACCESSORY METER ASSEMBLY
a. Replace the accessory meter with a normally functioning or new accessory meter (see
REMOVAL ).
b. Check that the accessory meter indicator operates normally.
OK: Accessory meter indicator operates normally.
NG: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
OK: END (ACCESSORY METER IS DEFECTIVE)
REAR VIEW MONITOR SYSTEM
PARTS LOCATION
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Parking Assist/Monitoring - Tundra
Fig. 47: Identifying Rear View Monitor System Replacement Parts Location (1 Of 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Parking Assist/Monitoring - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст