Toyota Tundra. Manual — part 2259

Fig. 412: Locating Drain Cock
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

c. Further tighten the drain cock within 360° so that the drain cock pipe is within the range shown in

the illustration.

3. INSTALL FRONT ENGINE MOUNTING INSULATOR RH

a. Install the mounting insulator with the nut.

Torque: 72 N*m (734 kgf*cm, 53 ft.*lbf)

Fig. 413: Locating Mounting Insulator With Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

4. INSTALL ENGINE ASSEMBLY

a. Install the engine assembly to the vehicle (See INSTALLATION ).

NOTE:



Do not rotate the drain cock more than 1 revolution (360°) after
tightening the drain cock to the specified torque.



Do not loosen the drain cock to adjust it. If an adjustment is
necessary, remove the drain cock and reinstall it.

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

REAR ENGINE MOUNTING

COMPONENTS

Fig. 414: Identifying Rear Engine Mounting Components With Torque Specifications
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

REMOVAL

1. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a. Support the transmission with a transmission jack. Lift the transmission slightly from the

crossmember.

Fig. 415: Supporting Transmission With Transmission Jack
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a. Remove the 4 rear engine mounting insulator bolts.

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

Fig. 416: Locating Rear Engine Mounting Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Remove the 4 nuts, 4 washers, 4 bolts and crossmember.

Fig. 417: Locating Nuts, Washers, Bolts And Crossmember
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

3. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a. Remove the 4 bolts and mounting insulator from the transmission.

Fig. 418: Locating Mounting Insulator And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Remove the bolt and mounting heat insulator.

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

INSTALLATION

1. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a. Install the mounting insulator to the transmission with the 4 bolts.

Torque: 59 N*m (602 kgf*cm, 44 ft.*lbf)

Fig. 419: Locating Mounting Insulator And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Install the mounting heat insulator with the bolt.

Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)

2. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a. Install the crossmember with the 4 bolts, 4 washers and 4 nuts.

Torque: 110 N*m (1122 kgf*cm, 81 ft.*lbf)

Fig. 420: Locating Crossmember With Bolts, Washers And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Install the 4 rear engine mounting insulator bolts.

Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf)

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra