Toyota Tundra. Manual — part 571
Fig. 400: Identifying z3 And J45 Cable Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE SPIRAL CABLE SUB-ASSEMBLY (See REMOVAL )
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY)
a. Disconnect the K18 receiver connector.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
(EAU)
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
CAUTION: The spiral cable is an important part of the SRS airbag system.
Incorrect removal or installation of the spiral cable may prevent
the airbag from deploying. Be sure to read the PRECAUTION for
the supplemental restraint system (see PRECAUTION ).
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY) TESTER
CONNECTION SPECIFIED CONDITION
Fig. 401: Identifying K18 Receiver Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
6. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMBINATION
METER)
a. Disconnect the K18 display connector.
b. Disconnect the J28 meter connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMBINATION METER)
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Switch Condition
Specified Condition
K18-2 (ILL+) - Body ground
Light control switch TAIL or HEAD
11 to 14 V
Light control switch OFF
Below 1 ohms
Tester Connection
Condition Specified Condition
K18-12 (ILL-) - J28-37 (ILL-) Always
Below 1 ohms
K18-12 (ILL-) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 402: Identifying K18 Display Connector And J28 Meter Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
PARKING BRAKE SWITCH CIRCUIT
DESCRIPTION
This circuit is from the parking brake switch to the navigation receiver.
WIRING DIAGRAM
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 403: Parking Brake Switch Circuit - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK BRAKE WARNING SWITCH
a. Check that the brake warning switch lights come on when the parking brake is applied and goes off
when it is released.
OK: The brake warning lights operate as specified above.
OK: Go to step 3
NG: Go to Next Step
2. INSPECT PARKING BRAKE SWITCH
a. Disconnect the A5 switch connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
PARKING BRAKE SWITCH TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Switch Condition
Specified Condition
A5-1 - Switch body
ON (When shaft is not pressed)
Below 1 ohms
OFF (When shaft is pressed)
10 Kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст