Toyota Tundra. Manual — part 896
Sliding roof in fully open or UP position
Vehicle speed 75 km/h (47 mph) or less (during acceleration)
2. Conditions that enable the sliding roof to automatically deflector UP:
Sliding roof in fully open or DOWN position
Vehicle speed 65 km/h (40 mph) or less (during deceleration)
6. CHECK FAIL-SAFE FUNCTION
a. If the sliding roof does not close because the jam protection function operates improperly, press the
TILT switch to up and hold it for 10 seconds or more. Then the sliding roof glass will be fully tilted
up. (It goes down a little after it is fully tilted up.) Then, you can manually close the sliding roof.
CUSTOMIZE PARAMETERS
1. CUSTOMIZING FUNCTION WITH TECHSTREAM
HINT:
The following items can be customized.
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on.
d. Enter the following menus:
Select: Customize Setting.
e. Select the setting by referring to the table below.
Sliding Roof
SLIDING ROOF - CUSTOMIZE PARAMETERS
NOTE:
When the customer requests a change in a function, first make sure
that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is
set to the default setting.
Display
(Item)
Default
Contents
Setting
Door Key
Related Open
ON
Function to manually open sliding roof linked with power
window if holding driver side door key for 3 seconds or more to
unlock position when ignition switch is OFF
ON /
OFF
Door Key
Related Close
ON
Function to manually close sliding roof linked with power
window if holding driver side door key for 3 seconds or more to
ON /
OFF
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
INITIALIZATION
1. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
a. Turn the ignition switch ON.
b. By pushing the SLIDE switch to close or the TILT switch to up on the roof console box, make the
sliding roof operate as follows:
TILT UP --> approximately 1 second --> TILT UP (The sliding roof lowers a little after it is fully
tilted up.)
c. Check that the sliding roof stops at the fully closed position.
d. Finish the initialization.
e. Check that the AUTO operation works normally.
HINT:
If the sliding roof cannot fully close or its position has become misaligned, perform the
initialization again.
If the sliding roof TILT switch to up or SLIDE switch to close is pressed and held until the
roof glass has either stopped moving or started moving in the opposite direction, and then the
switch is held for another 10 seconds or more, perform the initialization again.
If the AUTO operation function and jam protection function do not operate after the drive
gear has been initialized, replace the sliding roof drive gear (sliding roof ECU).
PROBLEM SYMPTOMS TABLE
HINT:
lock position when ignition switch is OFF
Door Key
Related
Operation
SLIDE
Function to select tilt up or slide open of manual sliding roof
operation linked with power window activated by holding driver
side door key for 3 seconds or more to unlock position when
ignition switch is OFF
TILT /
SLIDE
NOTE:
When replacing the sliding roof drive gear, the new sliding roof drive gear
requires initialization. If a reset is not executed, the following functions do
not operate: AUTO operation and jam protection function.
NOTE:
If the following conditions occur while operating, initialization will
fail.
Ignition switch is turned OFF.
Pushed sliding roof switch is released while sliding roof is
operating.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Use the table below to help determine the cause of the problem symptom. The potential causes of the
symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each
symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Sliding roof system
SLIDING ROOF - PROBLEM SYMPTOMS CHART
TERMINALS OF ECU
Fig. 5: Identifying W3 ECU Connector Terminal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
1. SLIDING ROOF DRIVE GEAR (SLIDING ROOF ECU)
a. Disconnect the W3 ECU connector.
b. Measure the voltage and resistance according to the value(s) in the table below.
W3 ECU CONNECTOR VOLTAGE AND RESISTANCE SPECIFICATION
Symptom
Suspected Area
See
Sliding function and
tilt function do not
operate
Sliding roof ECU
power source circuit
SLIDING ROOF ECU
POWER SOURCE
CIRCUIT
Either sliding
function or tilt
function does not
operate
Sliding roof control
switch circuit
SLIDING ROOF
CONTROL SWITCH
CIRCUIT
Key-linked open /
close operation does
not operate
Power door lock
control system
HOW TO PROCEED
WITH
TROUBLESHOOTING
Sliding roof drive
gear
SLIDING ROOF
HOUSING (FOR
CREWMAX)
Terminal No.
(Symbols)
Wiring Color
Terminal
Description
Condition
Specified
Condition
W3-1 (UP) - Body
LG - Body Sliding roof switch TILT switch is pressed Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
If the result is not as specified, there may be a malfunction on the wire harness side.
DTC CHECK/CLEAR
1. CHECK DTC
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on
d. Enter the following menus:
Select: Body Electrical / Sliding Roof / Trouble Codes.
e. Check the DTCs.
2. CLEAR DTC
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on.
d. Enter the following menus:
ground
ground
signal
to up
W3-1 (UP) - Body
ground
LG - Body
ground
Sliding roof switch
signal
TILT switch is not
pressed to up
10 kohms or
higher
W3-2 (DWN) -
Body ground
W - Body
ground
Sliding roof switch
signal
TILT switch is pressed
to down
Below 1 ohms
W3-2 (DWN) -
Body ground
W - Body
ground
Sliding roof switch
signal
TILT switch is not
pressed to down
10 kohms or
higher
W3-6 (OPN) - Body
ground
O - Body
ground
Sliding roof switch
signal
SLIDE switch is pressed
to open
Below 1 ohms
W3-6 (OPN) - Body
ground
O - Body
ground
Sliding roof switch
signal
SLIDE switch is not
pressed to open
10 kohms or
higher
W3-7 (CLS) - Body
ground
V - Body
ground
Sliding roof switch
signal
SLIDE switch is pressed
to close
Below 1 ohms
W3-7 (CLS) - Body
ground
V - Body
ground
Sliding roof switch
signal
SLIDE switch is not
pressed to close
10 kohms or
higher
W3-8 (E) - Body
ground
W-B - Body
ground
Ground
Always
Below 1 ohms
W3-9 (IG) - Body
ground
SB - Body
ground
IG power supply
Ignition switch ON
11 to 14 V
W3-9 (IG) - Body
ground
SB - Body
ground
IG power supply
Ignition switch OFF
Below 1 V
W3-10 (B) - Body
ground
L - Body
ground
+B power supply
Always
11 to 14 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст