Toyota Tundra. Manual — part 555
7. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKERS)
a. Disconnect the K16 amplifier connector.
b. Disconnect the K10, K12, N1, M1, O1, O2, O7 and O8 speaker connectors.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 331: Identifying K16 Amplifier Connector And K10, K12, N1, M1, O1, O2, O7 And O8
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Speaker Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKERS)
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
K16-6 (FR-) - K10-4 (TWR-)
Always
Below 1 ohms
K16-2 (FR+) - K10-3 (TWR+)
K16-7 (FL-) - K12-4 (TWL-)
K16-8 (FL+) - K12-3 (TWL+)
K10-2 (-) - M1-1
K10-1 (+) - M1-3
K12-2 (-) - N1-1
K12-1 (+) - N1-3
K16-4 (RR-) - O2-1 (-TW)
K16-10 (RR+) - O2-3 (+TW)
K16-9 (RL-) - O8-1 (-TW)
K16-3 (RL+) - O8-3 (+TW)
O2-4 (+) - O1-1
O2-2 (-) - O1-2
O8-4 (+) - O7-1
O8-2 (-) - O7-2
K16-8 (FL+) - Body ground
Always
10 kohms or higher
K16-7 (FL-) - Body ground
K16-2 (FR+) - Body ground
K16-6 (FR-) - Body ground
K16-3 (RL+) - Body ground
K16-9 (RL-) - Body ground
K16-10 (RR+) - Body ground
K16-4 (RR-) - Body ground
K10-2 (-) - Body ground
K10-1 (+) - Body ground
K12-2 (-) - Body ground
K12-1 (+) - Body ground
O2-3 (+TW) - Body ground
O2-1 (-TW) - Body ground
O8-3 (+TW) - Body ground
O8-1 (-TW) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
8. INSPECT FRONT NO. 3 SPEAKER LH
a. Disconnect the N1 speaker connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT NO. 3 SPEAKER LH TESTER CONNECTION SPECIFIED CONDITION
Fig. 332: Identifying N1 Speaker Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE FRONT NO. 3 SPEAKER LH (See REMOVAL )
OK: Go to Next Step
9. INSPECT FRONT NO. 3 SPEAKER RH
a. Disconnect the M1 speaker connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT NO. 3 SPEAKER RH TESTER CONNECTION SPECIFIED CONDITION
Tester Connection Condition Specified Condition
1 - 3
Always
2.5 to 3.5 ohms
Tester Connection Condition Specified Condition
1 -3
Always
2.5 to 3.5 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст