Toyota Tundra. Manual — part 899
OK: Go to Next Step
4. INSPECT ROOF CONSOLE BOX ASSEMBLY
a. Remove the roof console box with sliding roof switch (see REMOVAL ).
b. Measure the resistance according to the value(s) in the table below.
Fig. 8: Identifying Roof Console Box Assembly Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Standard resistance
ROOF CONSOLE BOX ASSEMBLY RESISTANCE SPECIFICATION
NG: REPLACE ROOF CONSOLE BOX ASSEMBLY (See REMOVAL )
OK: Go to Next Step
5. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)
a. Disconnect the W3 ECU connector.
Tester Connection
Switch Condition
Specified Condition
6 (UP) - 7(E)
TILT switch is pressed to up
Below 1 ohms
6 (UP) - 7(E)
TILT switch is not pressed to up
10 kohms or higher
5 (DWN) - 7 (E) TILT switch is pressed to down
Below 1 ohms
5 (DWN) - 7 (E) TILT switch is not pressed to down
10 kohms or higher
4 (OPN) - 7 (E)
SLIDE switch is pressed to open
Below 1 ohms
4 (OPN) - 7 (E)
SLIDE switch is not pressed to open 10 kohms or higher
3 (CLS) - 7 (E)
SLIDE switch is pressed to close
Below 1 ohms
3 (CLS) - 7 (E)
SLIDE switch is not pressed to close 10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Fig. 9: Identifying W3 ECU Connector And W7 Roof Console Box Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Disconnect the W7 roof console box connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)
RESISTANCE SPECIFICATION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (see DISASSEMBLY )
Tester Connection
Switch Condition Specified Condition
W3-1 (UP) - W7-6 (UP)
Always
Below 1 ohms
W3-2 (DWN) - W7-5 (DWN)
Always
Below 1 ohms
W3-6 (OPN) - W7-4 (OPN)
Always
Below 1 ohms
W3-7 (CLS) - W7-3 (CLS)
Always
Below 1 ohms
W7-6 (UP) - Body ground
Always
10 kohms or higher
W7-5 (DWN) - Body ground
Always
10 kohms or higher
W7-3 (CLS) - Body ground
Always
10 kohms or higher
W7-4 (OPN) - Body ground
Always
10 kohms or higher
W7-7 (E) - Body ground
Always
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
DTC B2343 POSITION INITIALIZATION INCOMPLETE
DESCRIPTION
This DTC is output when the sliding roof drive gear (sliding roof ECU) has not been initialized.
DTC B2343 POSITION INITIALIZATION INCOMPLETE DETECTION CONDITION CHART
WIRING DIAGRAM
Fig. 10: Sliding Roof Switch - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
a. Check that the sliding roof drive gear can be initialized (see INITIALIZATION ).
OK: Sliding roof drive gear can be initialized.
NG: GO TO STEP 3
OK: Go to Next Step
2. CHECK FOR DTC
a. Clear the DTCs (see DTC CHECK/CLEAR ).
DTC
Code
DTC Detection Condition
Trouble Area
B2343
Sliding roof drive gear (sliding roof ECU) has not been
initialized
Sliding roof drive gear (sliding roof
ECU)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
b. Check for DTCs (see DTC CHECK/CLEAR ).
Result
B2343 POSITION INITIALIZATION INCOMPLETE RESULT CHART
B: REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (see
DISASSEMBLY )
A: END
3. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)
a. Disconnect the W3 ECU connector.
Fig. 11: Identifying W3 ECU Connector And W7 Roof Console Box Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Disconnect the W7 roof console box connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
Result
Proceed to
No DTC is output
A
DTC B2343 is output
B
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст