Toyota Tundra. Manual — part 274
Sensor
Buzzer"
Stop
"4WD
Buzzer"
Stop
"Slide
Roof
Buzzer"
Stop
"Sports
Shift
Reject
Buzzer"
Meter Indicator
Function
Combination
Meter ECU
Main Body
ECU
ECM
Skid Control
ECU
Center
Airbag
Sensor
4WD
Control
ECU
Does not
illuminate or
always
illuminates
Light on
"Airbag
Warning
Light"
Light on
"BRAKE
Warning
Light"
Light on
"ABS
Warning
Light"
Data Recorder
Center
Airbag
Sensor
ECM
Combination
Meter ECU
Stop recording
Light on "ABS
Warning Light"
A/C
Air
Conditioning
Amplifier
Main Body
ECU
ECM
Combination
Meter ECU
Stop air
conditioner
Nothing
Remote Start
Bus Buffer
ECU
Main Body ECU Not possible to
control by
wireless
Nothing
4WD
4WD
Control
ECU
ECM
Skid Control
ECU with
Actuator
Combination
Meter ECU
Air
Not possible to
change
between 4WD
and 2WD
Nothing
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
DIAGNOSTIC TROUBLE CODE TABLE
HINT:
If a trouble code is displayed during the DTC check, inspect the trouble areas listed for that code. For details of
the code, refer to the table below.
CAN communication system:
DIAGNOSTIC TROUBLE CODE TABLE - CAN COMMUNICATION SYSTEM
Conditioning
Amplifier
(1)
MIL lights on only during VSC or ABS failure status.
DTC Code
Detection Item
Trouble Area
U0199
Lost Communication with "Door
Control Module A"
Power source circuit of
outer mirror control ECU
Outer mirror control ECU
Outer mirror control ECU
branch wire or connector
U0208
Lost Communication with "Seat
Control Module A"
Power source circuit of front
power seat control ECU and
switch LH
Front power seat control
ECU and switch LH
Front power seat control
ECU and switch LH branch
wire or connector
U1002
Lost Communication with
Gateway Module
MS bus circuit
Outer mirror control ECU
branch wire or connector
Front power seat control
ECU and switch LH branch
wire or connector
Multiplex tilt and telescopic
ECU branch wire or
connector
Main body ECU main wire
or connector
Combination meter ECU
main wire or connector
Outer mirror control ECU
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
DTC U0199: LOST COMMUNICATION WITH "DOOR CONTROL MODULE A"
DESCRIPTION
DTC DETECTION CONDITION AND TROUBLE AREA
WIRING DIAGRAM
Front power seat control
ECU and switch LH
Multiplex tilt and telescopic
ECU
Main body ECU
Combination meter ECU
No. 3 junction connector
U1115
Lost Communication with Tilt and
Telescopic Module
Power source circuit of
multiplex tilt and telescopic
ECU
Multiplex tilt and telescopic
ECU
Multiplex tilt and telescopic
ECU branch wire or
connector
DTC Code
DTC Detection Condition
Trouble Area
U0199
No communication from outer
mirror control ECU
Power source circuit of
outer mirror control ECU
Outer mirror control ECU
Outer mirror control ECU
branch wire or connector
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
Fig. 30: Identifying Lost Communication With "Door Control Module A" - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the
main wire and the branch wire.
2. CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU BRANCH WIRE)
a. Disconnect the N8 outer mirror control ECU connector.
b. Measure the resistance according to the value(s) in the table below.
CAUTION: Wait at least 90 seconds after disconnecting the cable from the
negative (-) battery terminal to prevent airbag and seat belt
pretensioner activation.
NOTE:
After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст