Toyota Tundra. Manual — part 355
If the result is not as specified, replace the door lock assembly.
b. Check the door lock position switch.
Fig. 110: Identifying Door Lock Position Switch With Connector Terminal LH (W/ Power
Window)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
1. Measure the resistance according to the value(s) in the table below.
Standard resistance IB]
DOOR LOCK POSITION SWITCH
If the result is not as specified, replace the door lock assembly.
c. Check the door lock and unlock switch.
Tester Connection Switch Condition Specified Condition
7 (LSSE) - 8 (E)
Unlock
Below 1 ohms
Lock
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Fig. 111: Identifying Door Lock And Unlock Switch LH (W/ Power Window)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
1. Measure the resistance according to the value(s) in the table below.
Standard resistance
DOOR LOCK AND UNLOCK SWITCH
If the result is not as specified, replace the door lock assembly.
2. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Power Window)
Tester Connection Switch Condition Specified Condition
9 (DLSR) - 7 (LSSR)
Lock
Below 1 ohms
10 (E) - 7 (LSSR)
Unlock
9 (DLSR) - 7 (LSSR)
Unlock
10 kohms or higher
10 (E) - 7 (LSSR)
Lock
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Fig. 112: Identifying Door Lock Motor RH (W/ Power Window)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Check the door lock motor.
1. Apply battery voltage to the door lock motor and check operation of the door lock motor.
OK
DOOR LOCK MOTOR
If the result is not as specified, replace the door lock assembly.
b. Check the door lock position switch.
1. Measure the resistance according to the value(s) in the table below.
Standard resistance
Measurement Condition
Specified Condition
Battery positive (+) --> Terminal 4 (L)
Battery negative (-) --> Terminal 1 (UL)
Lock
Battery positive (+) --> Terminal 1 (UL)
Battery negative (-) --> Terminal 4 (L)
Unlock
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
DOOR LOCK POSITION SWITCH
If the result is not as specified, replace the door lock assembly.
INSTALLATION
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE
FOR STANDARD BOLTS ).
1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH (See REASSEMBLY )
2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH (See
REASSEMBLY )
3. INSTALL FRONT DOOR LOCK ASSEMBLY LH (See REASSEMBLY )
4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH (See REASSEMBLY )
5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH (See REASSEMBLY )
6. INSTALL FRONT DOOR SERVICE HOLE COVER LH (See REASSEMBLY )
7. INSTALL FRONT NO. 1 DOOR TRIM BRACKET (See REASSEMBLY )
8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (See REASSEMBLY )
9. INSTALL FRONT DOOR ARMREST COVER LH
10. INSTALL COURTESY LIGHT ASSEMBLY (See INSTALLATION )
11. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See REASSEMBLY )
12. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)
(See REASSEMBLY )
13. INSTALL FRONT ARMREST UPPER BASE PANEL LH (See REASSEMBLY )
14. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH (See REASSEMBLY )
15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
REAR DOOR LOCK (FOR DOUBLE CAB)
COMPONENTS
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E)
Unlock
Below 1 ohms
Lock
10 kohms or higher
NOTE:
Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст