Toyota Tundra. Manual — part 1001
Fig. 20: Tightening Adjusting Nut Using SST
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for 2WD)
a. Apply MP grease to a new O-ring.
b. Install the O-ring to the axle hub.
c. Install the dust cover and axle hub to the steering knuckle with the 4 bolts.
Torque: 99 N*m (1010 kgf*cm, 73 ft.*lbf)
Fig. 21: Identifying Axle Hub Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for 4WD)
a. Apply MP grease to a new O-ring.
b. Install the O-ring to the axle hub.
NOTE:
Do not damage the O-ring.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Axle - Tundra
c. Connect the front drive shaft to the front axle hub.
d. Install the dust cover and axle hub to the steering knuckle with the 4 bolts.
Torque: 99 N*m (1010 kgf*cm, 73 ft.*lbf)
Fig. 22: Identifying Axle Hub Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. INSTALL FRONT AXLE HUB NUT LH (for 4WD)
a. Install the nut, front wheel adjusting lock cap and a new cotter pin.
Torque: 338 N*m (3446 kgf*cm, 249 ft.*lbf)
Fig. 23: Identifying Cotter Pin
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4. INSPECT FRONT AXLE HUB
a. Inspect the front axle hub (see ON-VEHICLE INSPECTION ).
5. INSTALL FRONT AXLE HUB GREASE CAP LH (for 4WD)
a. Install the axle hub grease cap.
NOTE:
Do not damage the O-ring.
NOTE:
Be careful not to damage the front drive shaft boot.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Axle - Tundra
6. INSTALL FRONT DISC LH (See INSTALLATION )
7. CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH
a. Connect the front disc brake caliper and install 2 new bolts.
Torque: 99 N*m (1010 kgf*cm, 73 ft.*lbf)
Fig. 24: Identifying Front Disc Brake Caliper Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Connect the brake tube bracket to the steering knuckle with the bolt.
Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf)
Fig. 25: Identifying Brake Tube Bracket
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8. INSTALL FRONT WHEEL
NOTE:
Make sure to securely fit the bearing to the axle hub.
NOTE:
Do not twist the flexible hose.
Make sure that the bolts are free from damage and foreign
matter.
Do not overtighten the bolts.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Axle - Tundra
Torque: for Aluminum Wheel
131 N*m (1336 kgf*cm, 97 ft.*lbf)
for steel Wheel
209 N*m (2131 kgf*cm, 154 ft.*lbf)
9. CHECK SPEED SENSOR SIGNAL
a. Check the speed sensor signal (see TEST MODE PROCEDURE ).
STEERING KNUCKLE
COMPONENTS
2009 Toyota Tundra
2009 DRIVELINE/AXLES Axle - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст