Toyota Tundra. Manual — part 2822
Fig. 65: Identifying Pressure Control Solenoid Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
HINT:
The shift solenoid valve SL2 is turned ON/OFF normally when the shift lever is on D:
SHIFT SOLENOID VALVE SL2 REFERENCE TABLE
1. INSPECT NO. 2 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)
a. Disconnect the D64 No. 2 transmission wire connector.
b. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SL2
ON
ON
ON
ON
OFF
OFF
Tester Connection
Condition Specified Condition
2 (SL2+) - 4 (SL2-)
20°C (68°F)
5.0 to 5.6 ohms
2 (SL2+) - Body ground
Always
10 kohms or higher
4 (SL2-) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Fig. 66: Identifying D64 No. 2 Transmission Wire Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: Go to step 3
OK: Go to next step.
2. CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - ECM)
a. Disconnect the D74 ECM connector.
b. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
Result
Tester Connection
Condition Specified Condition
D74-12 (SL2+) - D74-13 (SL2-) 20°C (68°F)
5.0 to 5.6 ohms
D74-12 (SL2+) - Body ground
Always
10 kohms or higher
D74-13 (SL2-) - Body ground
Always
10 kohms or higher
Result
Proceed To
NG
A
OK (for 3UR-FE)
B
OK (3UR-FBE)
C
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Fig. 67: Identifying D74 ECM Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: for 3UR-FE (See REMOVAL )
OK: for 3UR-FBE (See REMOVAL
3. INSPECT SHIFT SOLENOID VALVE SL2
a. Remove shift solenoid valve SL2.
b. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
c. Connect the battery's positive (+) lead with a 21 W bulb to terminal 1 and the negative (-) lead to
terminal 2 of the solenoid valve connector. Then check that the valve moves and makes an
operating noise.
OK: Valve moves and makes an operating noise.
Tester Connection Condition Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 ohms
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Fig. 68: Identifying Shift Solenoid Valve SL2
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE SHIFT SOLENOID VALVE SL2 (See REMOVAL )
OK: REPAIR OR REPLACE NO. 2 TRANSMISSION WIRE (See REMOVAL )
DTC P0781: 1-2 SHIFT (1-2 SHIFT VALVE)
DESCRIPTION
The 1-2 shift valve performs shifting to 1st gear and other gears. When shifting to 2nd and 4th gears is
impossible, or when the ECM directs the transmission to switch to 5th and 6th gear and the engine overruns
(clutch slips), this DTC is output.
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст