Toyota Tundra. Manual — part 242
Fig. 336: Locating Front No. 3 Speaker Assembly Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Detach the 3 claws and remove the speaker from the bracket.
Fig. 337: Identifying Front No. 3 Speaker Assembly Claws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION
1. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY (for Standard)
a. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
If the result is not as specified, replace the speaker assembly.
NOTE:
Do not touch the cone part of the speaker.
Tester Connection Condition Specified Condition
1 -2
Always
3.2 to 4.8 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 338: Identifying Front No. 1 Speaker Assembly Connector Terminals (For Standard)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY (for 12 Speakers)
a. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
If the result is not as specified, replace the speaker assembly.
Fig. 339: Identifying Front No. 1 Speaker Assembly Connector Terminals (For 12 Speakers)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY (for 12 Speakers)
a. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection Condition Specified Condition
1-2
Always
1.5 to 2.1 ohms
Tester Connection Condition Specified Condition
1-2
Always
2.5 to 3.5 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
If the result is not as specified, replace the speaker assembly.
Fig. 340: Identifying Front No. 3 Speaker Assembly Connectors Terminals (For 12 Speakers)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY (for 12 Speakers)
a. Attach the 3 claws to install the speaker to the bracket.
Fig. 341: Identifying Front No. 3 Speaker Assembly Claws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Install the speaker with bracket to the lower frame bracket garnish with the 3 screws.
NOTE:
Do not touch the cone part of the speaker.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 342: Locating Front No. 3 Speaker Assembly Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
Fig. 343: Locating Front No. 1 Speaker Assembly Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Temporarily install the speaker by attaching the claws of the speaker to the door panel.
b. Install the speaker with the 4 screws.
HINT:
Install the screws in the order shown in the illustration.
c. Connect the connector.
3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (See REASSEMBLY )
4. INSTALL FRONT DOOR ARMREST COVER LH
5. INSTALL COURTESY LIGHT ASSEMBLY (See REASSEMBLY )
6. INSTALL FRONT UPPER ARMREST BASE PANEL LH (See REASSEMBLY )
7. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH (See REASSEMBLY )
8. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH (See REASSEMBLY )
9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE:
Do not touch the cone part of the speaker.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст