Toyota Tundra. Manual — part 2646
Occupant Detection:
OCCUPANT DETECTION CONDITION TABLE
OK: Display changed correctly according to operation of buckle switch.
NG: Go to step 9
OK: Go to next step
5. READ VALUE USING TECHSTREAM (OCCUPANT DETECTION SENSOR)
a. Fasten the passenger side seat belt.
b. Turn the ignition switch ON, and wait for at least 60 seconds.
c. Using the Techstream, read the "Data List" (see DTC CHECK/CLEAR ).
Occupant Detection:
OCCUPANT DETECTION CONDITION TABLE
Tester Display
Measure Item/Range
Normal Condition
Diagnostic
Note
Passenger
Buckle SW
Passenger side buckle
switch/Set, Unset or NG
Set: Passenger side seat belt is
fastened
Unset: Passenger side seat belt is
unfastened
NG: Passenger side seat belt is
malfunctioning
-
Tester Display
Test Part
Control Range
Diagnostic
Note
FL Sensor Voltage
Front left sensor voltage/ Min.: 0 V
Max.: 19.8 V
0 to 4.7 V
-
FR Sensor Voltage
Front right sensor voltage/ Min.: 0 V
Max.: 19.8 V
0 to 4.7 V
-
RL Sensor Voltage
Rear left sensor voltage/ Min.: 0 V
Max.: 19.8 V
0 to 4.7 V
-
RR Sensor Voltage
Rear right sensor voltage/ Min.: 0 V
Max.: 19.8 V
0 to 4.7 V
-
FL Sensor Weight
Info
Front left sensor weight information/
Min.: -17 kg (-37.48 lb)
Max.: 27 kg (59.52 lb)
-17 to 27 kg (-37.48 to
59.52 lb)
-
FR Sensor Weight
Info
Front right sensor weight information/
Min.: -17 kg (-37.48 lb)
Max.: 27 kg (59.52 lb)
-17 to 27 kg (-37.48 to
59.52 lb)
-
RL Sensor Weight
Info
Rear left sensor weight information/
Min.: -17 kg (-37.48 lb)
Max.: 37 kg (81.57 lb)
-17 to 37 kg (-37.48 to
81.57 lb)
-
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
Result
RESULT TABLE
B: REPLACE OCCUPANT CLASSIFICATION ECU (See FRONT SEAT ASSEMBLY (FOR
FOLD DOWN SEAT TYPE) )
C: REPLACE OCCUPANT CLASSIFICATION ECU (See FRONT SEAT ASSEMBLY (FOR
POWER SEAT) )
A: Go to next step
6. REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
a. Turn the ignition switch OFF.
b. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
c. Replace the front seat frame with adjuster RH (see INITIALIZATION ).
HINT:
Perform the inspection using parts from a normal vehicle when possible.
7. PERFORM ZERO POINT CALIBRATION
a. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
b. Connect the Techstream to the DLC3.
c. Turn the ignition switch ON, and wait for at least 60 seconds.
d. Using the Techstream, perform the zero point calibration (see INITIALIZATION ).
8. PERFORM SENSITIVITY CHECK
a. Using the Techstream, perform the sensitivity check (see INITIALIZATION ).
Standard range:
RR Sensor Weight
Info
Rear right sensor weight information/
Min.:-17 kg (-37.48 lb)
Max.: 37 kg (81.57 lb)
-1.7 to 37 kg (-37.48 to
81.57 lb)
-
Total Weight
Information
Total weight information/ Min.: -68 kg
(-149.91 lb)
Max.: 128 kg (282.19 lb)
-68 to 128 kg (-149.91
to 282.19 lb)
-
Result
Proceed to
Display is as specified in normal
condition
A
Display is not as specified in normal
condition (for Manual Seat)
B
Display is not as specified in normal
condition (for Power Seat)
C
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
27 to 33 kg (59.5 to 72.8 lb)
NEXT: END
9. CHECK CONNECTOR
a. Disconnect the connectors from the occupant classification ECU and front seat inner belt RH.
b. Check that the connectors (on the occupant classification ECU side and front seat inner belt RH
side) are not damaged.
OK: Connectors are not deformed or damaged.
NG: REPLACE NO. 2 FLOOR WIRE
OK: Go to next step
10. REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a. Turn the ignition switch OFF.
b. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
c. Replace the front seat inner belt RH (see FRONT SEAT INNER BELT ASSEMBLY ).
d. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
11. PERFORM ZERO POINT CALIBRATION
a. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
b. Connect the Techstream to the DLC3.
c. Turn the ignition switch ON, and wait for at least 60 seconds.
d. Using the Techstream, perform the zero point calibration (see INITIALIZATION ).
12. PERFORM SENSITIVITY CHECK
a. Using the Techstream, perform the sensitivity check (see INITIALIZATION ).
Standard range:
27 to 33 kg (59.5 to 72.8 lb)
NEXT: END
13. CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY (PASSENGER AIRBAG
ON/OFF INDICATOR)
a. Turn the ignition switch ON, and wait for at least 60 seconds.
b. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds,
then turns off for approximately 2 seconds.
c. Approximately 6 seconds after the ignition switch is turned ON, check that the passenger airbag
ON/OFF indicator indicates ON/OFF according to the condition listed below.
Result
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
RESULT TABLE
OK: Passenger airbag ON/OFF indicator illuminates as specified in table above.
OK: Go to step 17
NG: Go to next step
14. RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
a. Turn the ignition switch OFF.
b. Loosen the 4 installation bolts of the front seat RH.
c. Tighten the 4 installation bolts of the front seat RH to the specified torque.
for Manual Seat (see INSTALLATION )
for Power Seat (see INSTALLATION )
Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf)
15. PERFORM ZERO POINT CALIBRATION
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON, and wait for at least 60 seconds.
c. Using the Techstream, perform the zero point calibration (see INITIALIZATION ).
OK: Zero point calibration is completed using tester.
NG: Go to step 16
OK: END
16. READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
a. Turn the ignition switch ON, and wait for at least 60 seconds.
b. Using the Techstream, read the "Data List" (see DTC CHECK/CLEAR ).
Occupant Detection:
Front Seat Passenger
Passenger Airbag Cutoff
Switch Position
ON
Indicator
OFF
Indicator
SRS Warning
Light
Adult seated
ON
ON
OFF
OFF
Adult seated
OFF
OFF
ON
OFF
Child seated/Child
restraint system set
AUTO
OFF
ON
OFF
Child seated/Child
restraint system set
OFF
OFF
ON
OFF
Vacant
ON
OFF
OFF
OFF
Vacant
OFF
OFF
ON
OFF
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст