Toyota Tundra. Manual — part 2942
Blinks (ON: 0.2 seconds,
OFF: 0.2 seconds)
malfunction
During shift position N signal
malfunction
During engine speed signal
malfunction
From 4WD HIGH to 4WD LOW return control completion,
until 4WD control switch is changed to 4H or 2WD
From 3 seconds after 4WD HIGH to 4WD LOW return control
start (shift fork of high-low transfer shift actuator is in neutral
position), until 4WD control switch is changed to 4H or 2WD
From 4WD LOW to 4WD HIGH return control completion,
until 4WD control switch is changed to 4L
From 3 seconds after 4WD LOW to 4WD HIGH return control
start (shift fork of high-low transfer shift actuator is in neutral
position), until 4WD control switch is changed to 4L
2009 Toyota Tundra
2009 TRANSMISSION JF1A Transfer - Tundra
Fig. 133: Identifying Switch Condition Chart
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms
are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking
the suspected areas in the order they are listed. Replace parts as necessary.
Touch select 2-4 and high-low system
TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM PROBLEM SYMPTOMS CHART
2009 Toyota Tundra
2009 TRANSMISSION JF1A Transfer - Tundra
Symptom
Suspected Area
See
Switch from 2WD to 4WD
HIGH impossible (Only 4HI
indicator light, or 4HI and 4LO
indicator lights blink at 0.2
seconds intervals)
Harness or connector
ON-VEHICLE INSPECTION
Transfer shift actuator
ON-VEHICLE INSPECTION
A.D.D. actuator
ON-VEHICLE INSPECTION
CAN communication system
CAN COMMUNICATION SYSTEM
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
Transfer
INSPECTION
Switch from 4WD HIGH to
4WD LOW impossible (Only
4LO indicator light, or 4HI and
4LO indicator lights blink at 0.2
seconds intervals)
Harness or connector
ON-VEHICLE INSPECTION
Transfer shift actuator
ON-VEHICLE INSPECTION
CAN communication system
CAN COMMUNICATION SYSTEM
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
Transfer
INSPECTION
Switch from 4WD HIGH to
2WD impossible (4HI and 4LO
indicator lights blink at 0.2
seconds intervals)
Harness or connector
ON-VEHICLE INSPECTION
Transfer shift actuator
ON-VEHICLE INSPECTION
A.D.D. actuator
ON-VEHICLE INSPECTION
CAN communication system
CAN COMMUNICATION SYSTEM
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
Transfer
INSPECTION
Switch from 4WD LOW to
4WD HIGH impossible (Only
4LO indicator light, or 4HI and
4LO indicator lights blink at 0.2
seconds intervals)
Harness or connector
ON-VEHICLE INSPECTION
Transfer shift actuator
ON-VEHICLE INSPECTION
CAN communication system
CAN COMMUNICATION SYSTEM
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
Transfer
INSPECTION
4HI indicator light does not
come on
Harness or connector
ON-VEHICLE INSPECTION
4WD fuse
ON-VEHICLE INSPECTION
Combination meter
HOW TO PROCEED WITH
TROUBLESHOOTING
CAN communication system
CAN COMMUNICATION SYSTEM
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
4HI indicator light remains on
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
Combination meter
HOW TO PROCEED WITH
TROUBLESHOOTING
4LO indicator light does not
come on
Combination meter
HOW TO PROCEED WITH
TROUBLESHOOTING
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
2009 Toyota Tundra
2009 TRANSMISSION JF1A Transfer - Tundra
TERMINALS OF ECU
1. CHECK 4WD CONTROL ECU
Fig. 134: Identifying 4WD Control ECU Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Measure the voltage and resistance according to the value(s) in the table below.
4WD CONTROL ECU TERMINAL DESCRIPTION
4HI indicator light remains on
4WD control switch
ON-VEHICLE INSPECTION
4WD control ECU
TERMINALS OF ECU
Combination meter
HOW TO PROCEED WITH
TROUBLESHOOTING
HINT:
*: Blinking during the return control is not a malfunction.
Terminal No.
(Symbols)
Wiring
Color
Terminal Description
Condition
Specified
Condition
A25-1 (HL1) -
A26-4 (GND)
O - W-B
High-low transfer shift
actuator limit switch
Ignition switch ON 4WD control
switch 4H
Below 1.5
V
Ignition switch ON 4WD control
switch 4L
10.5 to 14 V
A25-2 (HL2) -
A26-4 (GND)
R - W-B
High-low transfer shift
actuator limit switch
Ignition switch ON 4WD control
switch 4H
10.5 to 14 V
Ignition switch ON 4WD control
switch 4L
Below 1.5
V
A25-3 (HL3) -
A26-4 (GND)
GR - W-
B
High-low transfer shift
actuator limit switch
Ignition switch ON 4WD control
switch 4H
10.5 to 14 V
Ignition switch ON 1.5 seconds or
less after 4WD HIGH to 4WD
LOW switching operation
Below 1.5
V
Ignition switch ON Over 1.5
seconds after 4WD HIGH to 4WD
10.5 to 14 V
2009 Toyota Tundra
2009 TRANSMISSION JF1A Transfer - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст