Toyota Tundra. Manual — part 2074
a
Install a new gasket and the front No 2 exhaust pipe to the exhaust manifold LH with 3 new nuts
Torque: 54 N*m (551 kgf*cm, 40 ft.*lbf)
b
Install a new gasket and the front No 2 exhaust pipe to the front No 3 exhaust pipe with the 2 bolts
and 2 new nuts
Torque: 48 N*m (489 kgf*cm, 35 ft.*lbf)
c
Connect the air fuel ratio sensor connector
d
Connect the heated oxygen sensor connector
9
INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD) (See FRONT PROPELLER
SHAFT ASSEMBLY )
10
INSTALL PROPELLER SHAFT HEAT INSULATOR (for 4WD)
a
Install the heat insulator with the 2 bolts
Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf)
Fig. 22: Identifying Heat Insulator With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
11
CONNECT COOLER COMPRESSOR ASSEMBLY (See INSTALLATION )
12
INSTALL GENERATOR ASSEMBLY (See INSTALLATION )
13
CONNECT VANE PUMP ASSEMBLY (See INSTALLATION )
14
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE (See INSTALLATION )
15
INSTALL FAN SHROUD (See INSTALLATION )
16
INSTALL FAN AND GENERATOR V BELT (See INSTALLATION )
17
CONNECT OUTLET RADIATOR HOSE
18
CONNECT INLET RADIATOR HOSE
19
INSTALL AIR CLEANER ASSEMBLY (See INSTALLATION )
20
INSTALL AIR CLEANER HOSE ASSEMBLY (See INSTALLATION )
21
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
2009 Toyota Tundra
2009 ENG NE Exhaust (3UR-FE) - Tundra
22
ADD ENGINE COOLANT (See REPLACEMENT )
23
INSPECT FOR COOLANT LEAK (See ON-VEHICLE INSPECTION )
24
INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak Replace damaged parts as necessary
25
INSTALL FRONT FENDER APRON SEAL REAR LH
a
Install the fender apron seal with the 5 clips
26
INSTALL FRONT FENDER APRON SEAL LH
a
Install the fender apron seal with the 6 clips
27
INSTALL FRONT FENDER APRON SEAL REAR RH
a
Install the fender apron seal with the 5 clips
28
INSTALL FRONT FENDER APRON SEAL RH
a
Install the fender apron seal with the 6 clips
29
INSTALL NO. 1 ENGINE UNDER COVER (See REPLACEMENT )
30
INSTALL V-BANK COVER SUB-ASSEMBLY (See INSTALLATION )
EXHAUST PIPE (FOR REGULAR CAB STANDARD DECK)
COMPONENTS
NOTE:
Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).
2009 Toyota Tundra
2009 ENG NE Exhaust (3UR-FE) - Tundra
Fig. 23: Identifying Exhaust Pipe Components (Regular Cab Standard Deck) With Torque Specifications
(1 Of 3)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENG NE Exhaust (3UR-FE) - Tundra
Fig. 24: Identifying Exhaust Pipe Components (Regular Cab Standard Deck) With Torque Specifications
(2 Of 3)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENG NE Exhaust (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст