Toyota Tundra. Manual — part 432
B: REPLACE OIL PRESSURE SENDER GAGE ASSEMBLY (See REMOVAL
C: REPLACE OIL PRESSURE SENDER GAGE ASSEMBLY (See REMOVAL
D: REPLACE OIL PRESSURE SENDER GAGE ASSEMBLY (See REMOVAL
A
6. CHECK HARNESS AND CONNECTOR
Fig. 57: Checking Harness And Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Disconnect the J28 meter connector.
b. Disconnect the D77*1, E11*2 gauge connector.
*1: for 2UZ-FE
LED operates correctly according to engine condition
A
LED does not operate correctly according to engine condition (for 2UZ-FE)
B
LED does not operate correctly according to engine condition (for 3UR-FE)
C
LED does not operate correctly according to engine condition (for 3UR-FBE)
D
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
*2: for 3UR-FE, 3UR-FBE
c. Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE COMBINATION METER ASSEMBLY
VOLT METER MALFUNCTION
DESCRIPTION
The voltmeter indicates the voltage applied to the IG+ terminal of the combination meter.
WIRING DIAGRAM
Fig. 58: Volt Meter Malfunction - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
Tester Connection
Condition
Specified Condition
J28-11 (S) - D77*1-1
Always
Below 1 ohms
J28-11 (S) or D77*1-1 - Body
ground
Always
10 kohms or higher
J28-11 (S) - E11*2-1
Always
Below 1 ohms
J28-11 (S) or E11*2-1 - Body
ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
1. INSPECT FUSE (MET)
a. Remove the MET fuse from the engine room relay block.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FUSE (MET) RESISTANCE REFERENCE
NG: REPLACE FUSE
OK: Go to next step
2. PERFORM ACTIVE TEST BY TECHSTREAM (VOLTMETER)
a. Operate the Techstream according to the display and select "ACTIVE TEST" or "Active Test" (see
DATA LIST / ACTIVE TEST ).
Techstream
Combination Meter:
TECHSTREAM COMBINATION METER SPECIFICATIONS
OK: Needle indication is normal.
NG: REPLACE COMBINATION METER ASSEMBLY (see REMOVAL )
OK: Go to next step
3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY
GROUND)
a. Disconnect the J28 meter connector.
Tester Connection Condition Specified Condition
MET fuse
Always
Below 1 ohms
Tester Display Test Part Control Range
Diagnostic Note
Volt Meter
Operation
Voltmeter
0,3, 6, 9, 12, 15
or 18
Perform the test with the vehicle stopped and
engine idling
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
Fig. 59: Identifying J28 Meter Connector Terminal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Measure the resistance and voltage according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY
GROUND) RESISTANCE REFERENCE
Standard voltage
HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY
GROUND) VOLTAGE SPECIFICATIONS
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE COMBINATION METER ASSEMBLY (see REMOVAL )
COMBINATION METER
COMPONENTS
Tester Connection Condition Specified Condition
J28-40 (E1)
Always
Below 1 ohms
Tester Connection Switch Condition Specified Condition
J28-20 (IG+)
Ignition switch ON
11 to 14 V
Ignition switch OFF
Below 1 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст