Toyota Tundra. Manual — part 482
If the result is not as specified, the receiver may have a malfunction.
e. Using an oscilloscope, check the waveform.
Waveform (reference)
WAVEFORM REFERENCE
Fig. 73: Oscilloscope Waveform Graph
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. CHECK STEREO COMPONENT AMPLIFIER (see TERMINALS OF ECU )
DTC CHECK / CLEAR
K18-20
(GND)
R - W-B
image signal
lever R position
(refer to
WAVEFORM)
K7-23 (V-) -
K18-20
(GND)
Shielded
- W-B
Shielded ground
Always
Below 1 V
K7-17
(MACC) -
K18-20
(GND)
LG - W-
B
Microphone
amplifier power
supply
Ignition switch ACC
4 to 6 V
K7-19 (MIC+)
- K18-20
(GND)
BR - W-
B
Microphone voice
signal
See "Microphone & Voice
Recognition Check" (see
NAVIGATION CHECK
MODE )
-
K7-20 (MIC-)
- K18-20
(GND)
Y - W-B
Microphone voice
signal
See "Microphone & Voice
Recognition Check" (see
NAVIGATION CHECK
MODE )
-
Item
Content
terminal No. (Symbols) K7-22 (V+) - K7-21 (CGND)
Tool Setting
0.2 V/DIV., 0.2 µs/DIV.
Condition
Ignition switch ON, shift lever R position
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
HINT:
Illustrations may differ from the actual vehicle depending on the device settings and options. Therefore,
some detailed areas may not be exactly the same as on the actual vehicle.
If the system cannot enter the diagnostic mode, inspect all AVC-LAN communication components and
repair or replace problem parts (see AVC-LAN CIRCUIT ).
After the ignition switch is turned ON, check that the map is displayed before starting the diagnostic
mode. Otherwise, some items cannot be checked.
1. START DIAGNOSTIC MODE
a. Turn the ignition switch ACC.
b. Press the "DISP" switch.
Fig. 74: Identifying DISP Switch
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. From the display quality adjustment screen, touch the corners of the screen in the following order:
upper left --> lower left --> upper left --> lower left --> upper left --> lower left.
Fig. 75: Identifying Display Quality Adjustment Screen
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d. The diagnostic mode starts and the "System Check Mode" screen will be displayed. Service
inspection starts automatically and the result will be displayed.
2. FINISH DIAGNOSTIC MODE
a. Turn the ignition switch OFF.
3. DIAGNOSIS MENU
a. The "Diagnosis MENU" screen will be displayed by pressing the "Menu" switch on the "System
Check Mode" screen.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 76: Diagnostic Menu Screen Display - System Check Mode
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4. CHECK DTC
a. Read the system check result.
1. If the check result is "EXCH", "CHEK" or "Old", touch the displayed check result to view
the results on the "Unit Check Mode" screen and record them.
HINT:
If all check results are "OK", go to the communication DTC check.
If a device name is not known, its physical address is displayed.
HINT:
When proceeding to view the results of another device, press the "Service" switch to return to
the "System Check Mode" screen. Repeat this step.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 77: Diagnostic Menu Screen Display - System Check Mode
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Read the communication diagnostic check result.
1. Return to the "System Check Mode" screen, and press the "LAN Mon" switch to enter the
"LAN Monitor" screen.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст