Toyota Tundra. Manual — part 2765
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the
symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each
symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Tire Pressure Warning System
SYMPTOM TABLE
C2183/83
Transmitter ID3 not
received
transmitter
Tire pressure
warning
antenna and
receiver
Wire harness
or connector
Tire pressure
warning ECU
C2184/84
Transmitter ID4 not
received
Tire pressure
warning valve
and
transmitter
Tire pressure
warning
antenna and
receiver
Wire harness
or connector
Tire pressure
warning ECU
C2191/91
Vehicle speed
signal error
Combination
meter
Wire harness
or connector
Vehicle speed
signal circuit
Tire pressure
warning ECU
Symptom
Suspected Area
Reference
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
TERMINALS OF ECU
HINT:
Inspect the connectors from the back side.
1. CHECK TIRE PRESSURE WARNING ECU
Fig. 14: Identifying Tire Pressure Warning ECU Connector Terminals J31
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Disconnect the P17 tire pressure warning antenna and receiver connector.
b. Measure the voltage according to the value(s) in the table below.
CONNECTOR TERMINALS REFERENCE TABLE
Tire pressure warning light does
not illuminate despite tire pressure
decreasing
Check Data List (Tire inflation
pressure)
DATA LIST/ACTIVE TEST
ID code check (Registration)
REGISTRATION
Initialization
INITIALIZATION
Tire pressure warning light
remains illuminated (goes off
during initial check).
Tire Pressure Warning Light
Circuit
TIRE PRESSURE WARNING
LIGHT CIRCUIT
ECU Power Source Circuit
ECU POWER SOURCE
CIRCUIT
Tire pressure warning light
remains illuminated (comes on
during initial check).
Check Data List (Tire inflation
pressure)
DATA LIST/ACTIVE TEST
Tire pressure adjustment
TIRE PRESSURE WARNING
SYSTEM
ID code check (Registration)
REGISTRATION
Initialization
INITIALIZATION
Initialization cannot be done
Tire Pressure Warning Reset
Switch Circuit
TIRE PRESSURE WARNING
RESET SWITCH CIRCUIT
DTC check cannot be done
TC and CG Terminal Circuit
TC AND CG TERMINAL
CIRCUIT
ECU Power Source Circuit
ECU POWER SOURCE
CIRCUIT
Terminal No.
(Symbols)
Wiring
Color
Terminal Description
Condition
Specified
Condition
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
c. Connect the P17 tire pressure warning antenna and receiver connector.
d. Measure the voltage and resistance according to the value(s) in the table below.
VOLTAGE AND RESISTANCE SPECIFICATION TABLE
If the result is not as specified, the ECU may have a malfunction.
e. Using an oscilloscope, check the waveform 1.
J31-12 (RDA) - J31-
9 (GND)
G - W-B
Tire pressure warning antenna
and receiver signal
Ignition switch
ON
11 to 14 V
Terminal No.
(Symbols)
Wiring
Color
Terminal Description
Condition
Specified
Condition
J31-1 (CLSW)
- J31-9 (GND)
B - W-B
Tire pressure warning
reset switch
Ignition switch ON Tire
pressure warning reset switch
OFF
8 to 14 V
Ignition switch ON Tire
pressure warning reset switch
ON
Below 1.5 V
J31-2 (SPD) -
J31-9 (GND)
V - W-B Vehicle speed signal
Vehicle is running
Pulse
generation (See
d waveform 1)
J31-3 (TC) -
J31-9 (GND)
W - W-B TC terminal
When terminal TC is not
connected
8 to 14 V
J31-5 (IND) -
J31-9 (GND)
LG - W-
B
Tire pressure warning
light output signal
After ignition switch is turned
ON, when tire pressure
warning light illuminates for 3
seconds
2.2 to 4.4 V
Ignition switch ON Tire
pressure warning light off
Below 0.5 V
J31-6 (RF5V)
- J31-9 (GND)
Y - W-B
Tire pressure warning
antenna and receiver
power source
Ignition switch ON
11 to 14 V
J31-7 (IG) -
J31-9 (GND)
Y - W-B IG power source
Ignition switch ON
11 to 14 V
J31-9 (GND) -
Body ground
W-B -
Body
ground
Ground
Always
Below 1 ohms
J31-10 (SIL) -
J31-9 (GND)
L - W-B
Diagnosis tester
communication line
Ignition switch ON, when
communication is not
performed with a tester
8 to 14 V
J31-11
(GND2) - J31-
9 (GND)
P - W-B
Tire pressure warning
antenna and receiver
ground
Always
Below 1 ohms
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
WAVEFORM REFERENCE TABLE
Fig. 15: Waveform Graph 1
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
DIAGNOSIS SYSTEM
1. CHECK BATTERY VOLTAGE
Standard battery voltage: 11 to 14 V
If the voltage is below 11 V, recharge the battery before proceeding.
2. DIAGNOSIS SYSTEM
a. Warning light
1. When there is a problem with the tire pressure warning system, the tire pressure warning
light blinks at 0.5 second intervals, and turns on after 1 minute.
b. DTCs (Normal mode)
1. DTCs are stored in the tire pressure warning ECU and output by the blinks of the tire
pressure warning light or by using the Techstream (See DTC CHECK/CLEAR ).
c. Test mode
1. By switching from normal mode into test mode (input signal check), you can inspect the tire
pressure warning antenna and receiver, each tire pressure warning valve and transmitter, and
the vehicle speed sensor can be inspected (See TEST MODE PROCEDURE ).
Item
Contents
Terminal No. (Symbols) J31-2 (SPD) - J31-9 (GND)
Tool Setting
5 V/DIV., 200 ms/DIV.
Vehicle Condition
While driving at approximately 20 km/h (12 mph).
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст