Toyota Tundra. Manual — part 287
Fig. 73: Identifying Center Airbag Sensor Communication Stop Mode - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with
the CAN, which causes resistance variation.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the
main wire and the branch wire.
CAUTION: Wait at least 90 seconds after disconnecting the cable from the
negative (-) battery terminal to prevent airbag and seat belt
pretensioner activation.
NOTE:
After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
2. CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR BRANCH WIRE)
a. Disconnect the J46 center airbag sensor connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
STANDARD RESISTANCE SPECIFICATION TABLE
Fig. 74: Identifying J46 Center Airbag Sensor Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE CENTER AIRBAG SENSOR BRANCH WIRE OR CONNECTOR
(CANH, CANL)
OK: Go to Next Step
3. CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - BATTERY AND BODY
GROUND)
a. Reconnect the cable to the negative (-) battery terminal before measuring the resistances of the
main wire and the branch wire.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
STANDARD RESISTANCE SPECIFICATION TABLE
Tester Connection
Switch Condition Specified Condition
J46-13 (CANH) - J46-22 (CANL) Ignition switch OFF
54 to 69 ohms
Tester Connection
Condition Specified Condition
J46-25 (E1) - Body ground
Always
Below 1 ohms
J46-26 (E2) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
c. Measure the voltage according to the value(s) in the table below.
Standard voltage
STANDARD VOLTAGE SPECIFICATION TABLE
Fig. 75: Identifying J46 Center Airbag Sensor Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE CENTER AIRBAG SENSOR (See REMOVAL )
4WD CONTROL ECU COMMUNICATION STOP MODE
DESCRIPTION
SYMPTOM TABLE
WIRING DIAGRAM
Tester Connection
Switch Condition Specified Condition
J46-21 (IG2) - Body ground Ignition switch ON
11 to 14 V
Detection Item
Symptom
Trouble Area
4WD CONTROL ECU
COMMUNICATION STOP
MODE
When either condition below is met:
Four Wheel Drive Control is not displayed
on "CAN Bus Check".
Applies to "4WD CONTROL ECU
COMMUNICATION STOP MODE" in
"DTC COMBINATION TABLE".
Power source or
inside 4WD
control ECU
4WD control
ECU branch wire
or connector
4WD control
ECU
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
Fig. 76: Identifying 4WD Control ECU Communication Stop Mode Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with
the CAN, which causes resistance variation.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the
main wire and the branch wire.
2. CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU BRANCH WIRE)
a. Disconnect the A25 4WD control ECU connector.
CAUTION: Wait at least 90 seconds after disconnecting the cable from the
negative (-) battery terminal to prevent airbag and seat belt
pretensioner activation.
NOTE:
After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.
2009 Toyota Tundra
2009 ACCESSORIES & EQUIPMENT CAN Communication - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст