Toyota Tundra. Manual — part 222
The "Bluetooth" handsfree module is built into the radio receiver. If there is a problem between the
"Bluetooth" handsfree module and radio receiver, replace the radio receiver.
Component table:
COMPONENT TABLE
A: REPLACE RADIO RECEIVER (see REMOVAL )
B: REPLACE RADIO RECEIVER (see REMOVAL )
C: Go to next step.
3. CHECK POWER SOURCE CIRCUIT OF COMPONENT SHOWN BY SUB-CODE
a. Inspect the power source circuit of the component shown by the sub-code.
If the power source circuit is operating normally, proceed to the next step.
Component table:
COMPONENT TABLE
4. INSPECT RADIO RECEIVER
a. Disconnect the K4 and K22* receiver connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
Component
Proceed to
Radio Receiver (190) (for Column Shift Type)
A
Radio Receiver (190) (for Floor Shift Type)
B
Except Radio Receiver
C
Component
Proceed to
Stereo component
amplifier (440)
Stereo component amplifier power source circuit (see STEREO
COMPONENT AMPLIFIER POWER SOURCE CIRCUIT )
Television display
(1B0)*
Television display assembly power source circuit (see TELEVISION
DISPLAY POWER SOURCE CIRCUIT )
HINT:
*: w/ Rear Seat Entertainment System
Tester Connection
Condition Specified Condition
K4-5 (ATX+) - K4-15 (ATX-)
Always
60 to 80 ohms
K22-9 (TXM+) - K22-10 (TXM-)* Always
60 to 80 ohms
HINT:
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Result:
RESULT REFERENCE
B: REPLACE RADIO RECEIVER (see REMOVAL )
C: REPLACE RADIO RECEIVER (see REMOVAL )
Fig. 249: Identifying K4 And K22 Connectors Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
A: Go to next step.
5. CHECK HARNESS AND CONNECTOR ("BLUETOOTH" HANDSFREE MODULE
COMPONENT SHOWN BY SUB-CODE)
*: w/ Rear Seat Entertainment System
Result
Proceed to
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 250: AVC-LAN Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Start the check from the circuit that is near the component shown by the sub-code first.
For details of the connectors, refer to the "TERMINALS OF ECU" .
a. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the
"Bluetooth" handsfree module and the component shown by the sub-code.
1. Disconnect all connectors between the "Bluetooth" handsfree module and the component
shown by the sub-code.
2. Check for an open or short in the AVC-LAN circuit between the "Bluetooth" handsfree
module and the component shown by the sub-code.
OK: There is no open or short circuit.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step.
6. REPLACE COMPONENT SHOWN BY SUB-CODE
a. Replace the component shown by the sub-code with a normal one and check if the same problem
occurs again.
OK: Same problem does not occur.
Result:
RESULT REFERENCE
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
B: REPLACE RADIO RECEIVER (BUILT-IN "BLUETOOTH" HANDSFREE MODULE) (see
REMOVAL )
C: REPLACE RADIO RECEIVER (BUILT-IN "BLUETOOTH HANDSFREE MODULE") (see
REMOVAL )
A: END
RADIO RECEIVER POWER SOURCE CIRCUIT
DESCRIPTION
This circuit provides power to the radio receiver.
WIRING DIAGRAM
Result
Proceed to
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст