Toyota Tundra. Manual — part 1255
To check the air pump operation, use the Air Injection Check function described in the System
Check.
NG : REPLACE AIR PUMP ASSEMBLY . (See AIR PUMP ).
Fig. 220: Identifying Air Pump Connector Terminals
OK : Go to next step.
8. INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER
POWER SOURCE CIRCUIT) (See INSPECTION PROCEDURE )
NG : REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE
CIRCUIT
OK : Go to next step.
9. CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a. Disconnect the D74 ECM connector.
b. Disconnect the D51 or D55 AID connector.
c. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
D74-54 (AIRP) - D55-4 (SIP)
Always
Below 1 ohms
D74-53 (ARP2) - D51-4 (SIP2) Always
Below 1 ohms
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Fig. 221: Identifying D74 ECM Connector & D51 Or D55 Aid Connector
OK : Go to next step.
10. REPLACE AIR INJECTION CONTROL DRIVER
a. Replace the air injection control driver. (See AIR INJECTION DRIVER ).
11. CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447) (See
INSPECTION PROCEDURE )
NG : REPLACE ECM (See REMOVAL )
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
OK : END
DTC P2610 ECM/PCM INTERNAL ENGINE OFF TIMER PERFORMANCE
DTC SUMMARY
DTC SUMMARY CHART
DESCRIPTION
To ensure the accuracy of the EVAP (Evaporative Emission) monitor values, the soak timer, which is built into
the ECM, measures 5 hours (+/-15 minutes) from when the ignition switch is turned OFF, before the monitor is
run. This allows the fuel to cool down, which stabilizes the EVAP pressure. When 5 hours have elapsed, the
ECM turns on.
Fig. 222: ECM/PCM Internal Engine Off Timer Performance - Circuit Diagram
MONITOR DESCRIPTION
5 hours after the ignition switch is turned OFF, the soak timer activates the ECM to begin the EVAP system
monitor. While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU
clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and sets
the DTC (2 trip detection logic).
MONITOR STRATEGY
DTC
Monitoring Item
Malfunction Detection
Condition
Trouble
Area
Detection
Timing
Detection
Logic
P2610
Soak timer (built into
ECM)
ECM internal malfunction
ECM
Engine running 2 trip
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS
INSPECTION PROCEDURE
HINT:
DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM
replacement is necessary.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was
moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other
data from the time the malfunction occurred.
1. REPLACE ECM
a. Replace the ECM (See REMOVAL ).
2. CHECK WHETHER DTC OUTPUT RECURS
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the Techstream ON.
d. Clear DTCs (See DTC CHECK/CLEAR ).
e. Start the engine and wait for 10 minutes or more.
f. Enter the following menus: Powertrain/Engine and ECT/Trouble Codes/Pending.
g. If no pending DTC is displayed, the repair has been successfully completed.
Required Sensors/Components
ECM
Frequency of Operation
Once per driving cycle
Duration
10 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None
Monitor runs whenever following DTC not present
None
Ignition switch
ON
Engine
Running
Battery voltage
8 V or more
Starter
OFF
Soak timer measurement when ECM CPU clock counts 10
minutes
Less than 7 minutes, or more than 13
minutes
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст