Toyota Tundra. Manual — part 146
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Press the preset switch "3" to change to "Detailed Information Mode".
c. Identify the component which has stored this code.
Component table:
COMPONENT TABLE
HINT:
"440 (stereo component amplifier)" is the component which has stored this code in the
example shown in the illustration.
For details of the DTC display, refer to "DTC CHECK / CLEAR" .
5. CHECK COMPONENT WHICH HAS STORED THIS CODE
a. Select the component which has stored this code.
Component table:
COMPONENT TABLE
NEXT: END
DTC 01-DD MASTER RESET; DTC 01-E1 VOICE PROCESSING DEVICE ON ERROR
DESCRIPTION
DTC TROUBLE DETECTION CONDITION
Component
Physical address
Stereo component amplifier
440
"Bluetooth" handsfree module
19D
Radio receiver
190
Component
Proceed to
Stereo component
amplifier
Stereo component amplifier communication error (see STEREO
COMPONENT AMPLIFIER COMMUNICATION ERROR )
"Bluetooth"
handsfree module
"Bluetooth" handsfree module communication error (see BLUETOOTH
HANDSFREE MODULE COMMUNICATION ERROR )
Radio receiver
Radio receiver communication error (see RADIO RECEIVER
COMMUNICATION ERROR )
DTC
No.
DTC Detection Condition
Trouble Area
01-
DD*1
The device that should be the master has been
disconnected after engine start.
Radio receiver power source circuit
AVC-LAN circuit between the radio
receiver and the component which has
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
INSPECTION PROCEDURE
1. CHECK RADIO RECEIVER POWER SOURCE CIRCUIT
a. Refer to the RADIO RECEIVER POWER SOURCE CIRCUIT .
If the power source circuit is operating normally, proceed to the next step.
2. INSPECT RADIO RECEIVER
a. Disconnect the K4 receiver connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
Result:
RESULT REFERENCE
01-
E1*2
The AMP device records that the AMP output
does not function even while the source device
operates.
stored this code
Radio receiver
Component which has stored this code
HINT:
*1: This code may be stored if the engine is started and the ignition switch is turned to START position
again.
*2: Even if no fault is present, this trouble code may be stored depending on the battery condition or
engine start voltage.
NOTE:
Before starting troubleshooting, be sure to clear DTCs to erase codes
stored due to the reasons described in the HINT above. Then, check for
DTCs and troubleshoot according to the output DTCs.
The radio receiver is the master unit.
Be sure to clear and recheck DTCs after the inspection is completed to
confirm that no DTCs are output.
NOTE:
Be sure to read the DESCRIPTION before performing the following procedures.
Tester Connection
Condition Specified Condition
K4-5(ATX+) - K4-15 (ATX-) Always
60 to 80 ohms
Result
Proceed to
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
B: REPLACE RADIO RECEIVER (see REMOVAL )
C: REPLACE RADIO RECEIVER (see REMOVAL )
Fig. 31: Identifying K4 Receiver Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
A: Go to Next Step
3. IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
a. Enter the diagnostic mode.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 32: Service Check Mode And Detailed Information Diagnostic Mode Flow Chart
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Press the preset switch "3" to change to "Detailed Information Mode".
c. Identify the component which has stored this code.
Component table:
COMPONENT TABLE
HINT:
"440 (stereo component amplifier)" is the component which has stored this code in the
example shown in the illustration.
Component
Physical address
Stereo component amplifier
440
"Bluetooth" handsfree module
19D
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст