Toyota Tundra. Manual — part 679
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 521: Identifying Power Seat Switch Components (2 Of 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. REMOVE FRONT SEAT ASSEMBLY LH
a. Remove the front seat (see REMOVAL ).
2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH (see DISASSEMBLY )
3. REMOVE RECLINING POWER SEAT SWITCH KNOB LH (see DISASSEMBLY )
4. REMOVE FRONT SEAT CUSHION SHIELD LH (see DISASSEMBLY )
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
5. REMOVE LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch) (see
DISASSEMBLY )
6. REMOVE FRONT POWER SEAT SWITCH LH (see DISASSEMBLY )
INSPECTION
1. INSPECT FRONT POWER SEAT SWITCH LH
a. Measure the resistance according to the value(s) in the table below.
Standard resistance:
Slide switch
SLIDE SWITCH
Front vertical switch
FRONT VERTICAL SWITCH
Lifter switch
LIFTER SWITCH
Tester Connection Switch Condition Specified Condition
9 (SLDF) - 1 (B)
FRONT
Below 1 ohms
6 (SLDR) - 4 (E)
9 (SLDF) - 4 (E)
OFF
6 (SLDR) - 4 (E)
9 (SLDF) - 4 (E)
REAR
6 (SLDR) -1 (B)
Tester Connection Switch Condition Specified Condition
10 (FUP) -1 (B)
UP
Below 1 ohms
5 (FDWN) - 4 (E)
10 (FUP) - 4 (E)
OFF
5 (FDWN) - 4 (E)
10 (FUP)- 4 (E)
DOWN
5 (FDWN) -1 (B)
Tester Connection Switch Condition Specified Condition
7 (LUP) - 1 (B)
UP
Below 1 ohms
8 (LDWN) - 4 (E)
7 (LUP) - 4 (E)
OFF
8 (LDWN) - 4 (E)
7 (LUP) - 4 (E)
DOWN
8 (LDWN) - 1 (B)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
Reclining switch
RECLINING SWITCH
If the result is not as specified, replace the switch.
Fig. 522: Inspecting Front Power Seat Switch LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Tester Connection Switch Condition Specified Condition
3 (RCLF) - 1 (B)
FRONT
Below 1 ohms
2 (RCLR) - 4 (E)
3 (RCLF) - 4 (E)
OFF
2 (RCLR) - 4 (E)
3 (RCLF) - 4 (E)
REAR
2 (RCLR) - 1 (B)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
2. INSPECT FRONT POWER SEAT SWITCH RH
a. Measure the resistance according to the value(s) in the table below.
Standard resistance:
Slide switch
SLIDE SWITCH
Reclining switch
RECLINING SWITCH
If the result is not as specified, replace the switch.
Tester Connection Switch Condition Specified Condition
9 (SLDF) - 1 (B)
FRONT
Below 1 ohms
6 (SLDR) - 4 (E)
9 (SLDF) - 4 (E)
OFF
6 (SLDR) - 4 (E)
9 (SLDF) - 4 (E)
REAR
6 (SLDR) -1 (B)
Tester Connection Switch Condition Specified Condition
3 (RCLF) - 1 (B)
FRONT
Below 1 ohms
2 (RCLR) - 4 (E)
3 (RCLF) - 4 (E)
OFF
2 (RCLR) - 4 (E)
3 (RCLF) - 4 (E)
REAR
2 (RCLR) - 1 (B)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст