Toyota Tundra. Manual — part 358
2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH (See DISASSEMBLY )
3. REMOVE REAR UPPER DOOR ARMREST BASE PANEL LH (See DISASSEMBLY )
4. REMOVE REAR DOOR FRAME GARNISH LH (See DISASSEMBLY )
5. REMOVE COURTESY LIGHT ASSEMBLY (See DISASSEMBLY )
6. REMOVE REAR DOOR ARMREST COVER LH
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (See DISASSEMBLY )
8. REMOVE REAR NO. 2 DOOR TRIM BRACKET (See DISASSEMBLY )
9. REMOVE REAR DOOR SERVICE HOLE COVER LH (See DISASSEMBLY )
10. REMOVE REAR DOOR GLASS RUN LH (See DISASSEMBLY )
11. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH (See
DISASSEMBLY )
12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH (See DISASSEMBLY )
13. REMOVE REAR DOOR LOCK ASSEMBLY LH (See DISASSEMBLY )
14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH (See
DISASSEMBLY )
15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH (See DISASSEMBLY )
INSPECTION
1. INSPECT REAR DOOR LOCK ASSEMBLY LH
NOTE:
Some systems need to be initialized after the cable is reconnected
(see INITIALIZATION ).
After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Fig. 119: Identifying Rear Door Lock Assembly LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Check the door lock motor.
1. Apply battery voltage to the door lock and check operation of the door lock.
OK
DOOR LOCK MOTOR
If the result is not as specified, replace the door lock assembly.
b. Check the door lock position switch.
1. Measure the resistance according to the value(s) in the table below.
Standard resistance
Measurement Condition
Specified Condition
Battery positive (+) --> Terminal 4 (L)
Battery negative (-) --> Terminal 1 (UL)
Lock
Battery positive (+) --> Terminal 1 (UL)
Battery negative (-) --> Terminal 4 (L)
Unlock
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
DOOR LOCK POSITION SWITCH
If the result is not as specified, replace the door lock assembly.
2. INSPECT REAR DOOR LOCK ASSEMBLY RH
Fig. 120: Identifying Rear Door Lock Assembly RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Check the door lock motor.
1. Apply battery voltage to the door lock and check operation of the door lock.
OK
DOOR LOCK MOTOR
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E)
Unlock
Below 1 ohms
Lock
10 kohms or higher
Measurement Condition
Specified Condition
Battery positive (+) --> Terminal 4 (L)
Battery negative (-) --> Terminal 1 (UL)
Lock
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
If the result is not as specified, replace the door lock assembly.
b. Check the door lock position switch.
1. Measure the resistance according to the value(s) in the table below.
Standard resistance
DOOR LOCK POSITION SWITCH
If the result is not as specified, replace the door lock assembly.
INSTALLATION
1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH (See REASSEMBLY )
2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH (See
REASSEMBLY )
3. INSTALL REAR DOOR LOCK ASSEMBLY LH (See REASSEMBLY )
4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH (See REASSEMBLY )
5. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH (See
REASSEMBLY )
6. INSTALL REAR DOOR GLASS RUN LH (See REASSEMBLY )
7. INSTALL REAR DOOR SERVICE HOLE COVER LH (See REASSEMBLY )
8. INSTALL REAR NO. 2 DOOR TRIM BRACKET (See REASSEMBLY )
9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (See REASSEMBLY )
10. INSTALL REAR DOOR ARMREST COVER LH
11. INSTALL COURTESY LIGHT ASSEMBLY (See REASSEMBLY )
12. INSTALL REAR DOOR FRAME GARNISH LH (See REASSEMBLY )
13. INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH (See REASSEMBLY )
14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH (See REASSEMBLY )
15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
DOOR CONTROL RECEIVER (FOR DOUBLE CAB)
Battery positive (+) --> Terminal 1 (UL)
Battery negative (-) --> Terminal 4 (L)
Unlock
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E)
Unlock
Below 1 ohms
Lock
10 kohms or higher
NOTE:
Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст