Toyota Tundra. Manual — part 1009
DIFFERENTIAL OIL
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL
a. Stop the vehicle on a level place.
b. for Front Differential:
1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.
2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.
3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.
Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf)
c. for Rear Differential:
1. Remove the filler plug and gasket.
2. Remove the drain plug and gasket, and drain the oil.
3. Install a new gasket and the drain plug.
Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf)
2. ADD DIFFERENTIAL OIL
a. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of
the differential filler plug hole.
Oil leakage from rear differential
Rear differential carrier oil seal
(worn or damaged)
DIFFERENTIAL CARRIER
OIL SEAL (FOR 3UR-FE)
Companion flange (loose or
damaged)
DIFFERENTIAL CARRIER
ASSEMBLY (FOR 3UR-FE)
Oil leak from rear differential
drive pinion shaft
Oil (level too high or wrong
grade)
DIFFERENTIAL OIL
Rear differential carrier oil seal
(worn or damaged)
DIFFERENTIAL CARRIER
OIL SEAL (FOR 3UR-FE)
Companion flange (loose or
damaged)
DIFFERENTIAL CARRIER
ASSEMBLY (FOR 3UR-FE)
2009 Toyota Tundra
2009 DRIVELINE/AXLES Differential - Tundra
Fig. 1: Checking Differential Oil Level
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Oil type
DIFFERENTIAL OIL TYPE SPECIFICATIONS
Front differential capacity
FRONT DIFFERENTIAL OIL CAPACITY
Rear differential capacity
REAR DIFFERENTIAL OIL CAPACITY
NOTE:
Too much or too little oil will lead to differential problems.
After changing the oil, drive the vehicle and then check the oil
level again.
Item
Oil type and viscosity
Front differential
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
Rear differential
Specified Condition
2.05 to 2.15 liters (2.2 to 2.3 US qts., 1.8 to 1.9 lmp. qts.)
Engine type
Wheelbase type Cab type
Drive
type
Specified Condition
3UR-FE
3220 mm (10 ft.
6.8 in.)
Regular
2WD
3.40 to 3.50 liters (3.6 to 3.7 US qts., 3.0
to 3.1 lmp. qts.)
4WD
3700 mm (12 ft.
1.7 in.)
Regular
2WD
3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1
to 3.2 lmp. qts.)
4WD
Double
2WD
4WD
CrewMax
2WD
3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2
to 3.3 lmp. qts.)
4WD
3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1
to 3.2 lmp. qts.)
4180 mm (13 ft.
8.6 in.)
Double
2WD
3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2
to 3.3 lmp. qts.)
4WD
1GR-FE and
2UZ-FE
3220 mm (10 ft.
6.8 in.)
Regular
2WD
4.00 to 4.10 liters (4.2 to 4.3 US qts., 3.5
to 3.6 lmp. qts.)
4WD
3700 mm (12 ft.
1.7 in.)
ALL
2WD
4.55 to 4.65 liters (4.8 to 4.9 US qts., 4.0
to 4.1 lmp. qts.)
4WD
4180 mm (13 ft.
8.6 in.)
2WD
4WD
2009 Toyota Tundra
2009 DRIVELINE/AXLES Differential - Tundra
b. for Rear Differential:
1. Install a new gasket and the filler plug.
Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf)
c. for Front Differential:
1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.
Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf)
DIFFERENTIAL CARRIER OIL SEAL (FOR 1GR-FE, 2UZ-FE)
COMPONENTS
2009 Toyota Tundra
2009 DRIVELINE/AXLES Differential - Tundra
Fig. 2: Identifying Differential Carrier Oil Seal Components With Torque Specifications (For 1GR-FE,
2UZ-FE)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL (see REPLACEMENT )
2. REMOVE PROPELLER SHAFT ASSEMBLY
a. Remove the propeller shaft for 2WD (see PROPELLER SHAFT ASSEMBLY (FOR 2WD) ).
b. Remove the propeller shaft for 4WD (see PROPELLER SHAFT ASSEMBLY (FOR 4WD) ).
2009 Toyota Tundra
2009 DRIVELINE/AXLES Differential - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст