Toyota Tundra. Manual — part 2050
Fig. 403: Identifying Fuel Tube
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
33
INSTALL ENGINE WIRE
a
Install the engine wire
b
Engine Rear Side:
1
Install the 3 wires with the 3 bolts
Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf)
2
Connect the 5 clamps
3
Connect the 2 air switching valve connectors
Fig. 404: Locating Engine Wire, Clamps And Air Switching Valve Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Engine RH Side:
1
Connect the 7 clamps
2
Connect the oil pressure sender gauge connector
3
Connect the throttle sensor connector
4
Connect the noise filter connector
5
Connect the fuel injector connector
6
Connect the 2 VVT sensor connectors
7
Connect the 4 ignition coil connectors
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 405: Locating Ignition Coil Connectors (Engine RH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8
Connect the 2 camshaft timing control valve connectors
d
Engine LH Side:
1
Connect the 7 clamps and install the engine wire with the bolt
Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)
2
Connect the noise filter connector
3
Connect the fuel injector connector
4
Connect the engine coolant temperature sensor connector
5
Connect the purge VSV connector
6
Connect the vacuum switching valve connector (for ACIS)
7
Connect the camshaft position sensor connector
8
Connect the 2 VVT sensor connectors
9
Connect the 4 ignition coil connectors
Fig. 406: Locating Ignition Coil Connectors (Engine LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
10
Connect the 2 camshaft timing control valve connector
FRONT ENGINE MOUNTING
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
COMPONENTS
Fig. 407: Exploded View Of Front Engine Mounting With Torque Specifications
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1
REMOVE ENGINE ASSEMBLY
a
Remove the engine assembly from the vehicle (see REMOVAL )
2
REMOVE FRONT ENGINE MOUNTING INSULATOR RH
a
Remove the nut and mounting insulator
Fig. 408: Locating Front Engine Mounting Insulator With Nut - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
REMOVE WATER DRAIN COCK SUB-ASSEMBLY
a
Remove the drain cock from the cylinder block LH side
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 409: Locating Water Drain Cock
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4
REMOVE FRONT ENGINE MOUNTING INSULATOR LH
a
Remove the nut and mounting insulator
Fig. 410: Locating Front Engine Mounting Insulator With Mounting Nut - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1
INSTALL FRONT ENGINE MOUNTING INSULATOR LH
a
Install the mounting insulator with the nut
Torque: 72 N*m (734 kgf*cm, 53 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст