Toyota Tundra. Manual — part 315
1. CHECK INDICATOR
a. Turn the ignition switch ON.
b. Check that the CRUISE main indicator light illuminates when the cruise control main switch is
turned ON, and that the indicator light turns off when the main switch is turned OFF. If the results
are not as specified, inspect the CRUISE main indicator light circuit (see CRUISE MAIN
INDICATOR LIGHT CIRCUIT ).
Fig. 10: Identifying CRUISE Main Indicator Light
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
While driving with cruise control, the ECM activates AUTO CANCEL of the cruise control system
when a malfunction in one of the following occurs: vehicle speed sensors, stop light switch or other
related parts. When AUTO CANCEL is activated, the CRUISE main indicator light outputs the
blinking pattern shown in the illustration. At the same time, data of the malfunction is stored as a
DTC.
Fig. 11: CRUISE Main Indicator Light Blinking Pattern
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
DTC CHECK / CLEAR
1. CHECK DTC
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Cruise Control - Tundra
c. Turn the tester on.
d. Enter the following menus:
Techstream - Select: Powertrain / Engine and ECT / Trouble Codes.
e. Read the DTCs.
2. CLEAR DTC
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on.
d. Enter the following menus:
Techstream - Select: Powertrain / Engine and ECT / Trouble Codes.
e. Erase the DTCs.
FAIL-SAFE CHART
HINT:
If the following conditions are detected while the cruise control is in operation, the system clears the stored
vehicle speed in the ECM and cancels the cruise control operation.
FAIL-SAFE CHART
Vehicle Condition
Auto Cancel Condition
Fail-safe Deactivation Condition
CRUISE main indicator light
blinks
There is open or short in
stop light switch circuit
There is problem with
vehicle speed signal
There is problem with
throttle position sensor and
motor
Turn cruise control main switch
ON again
CRUISE main indicator light
blinks
There is problem with input
circuit of stop light switch
circuit
There is problem with
cancel circuit
Turn cruise control main
switch ON again
Turn ignition switch OFF
CRUISE main indicator light goes
off
Vehicle speed is lower than
low speed limit (approx. 40
km/h (25 mph)) while
running with cruise control
on
Vehicle speed is lower than
Push cruise control main switch to
RESUME/ACCEL
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Cruise Control - Tundra
DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using the Techstream to read the DATA LIST allows values or states of switches, sensors, actuators and
other items to be read without removing any parts. This non-intrusive inspection can be very useful
because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading
the DATA LIST information early in troubleshooting is one way to save diagnostic time.
a. Warm up the engine.
b. Turn the ignition switch OFF.
c. Connect the Techstream to the DLC3.
d. Turn the ignition switch ON.
e. Turn the tester on.
f. Enter the following menus:
Techstream - Select: Powertrain / Engine and ECT / Data List.
g. According to the display on tester, read the "DATA LIST".
Techstream
CRUISE CONTROL
stored speed by approx. 16
km/h (9.9 mph) or more
NOTE:
In the tables below, the values listed under "Normal Condition" are
reference values. Do not depend solely on these reference values when
deciding whether a part is faulty or not.
Tester Display
Measurement
Item/Range
Normal Condition
Diagnostic Note
CCS Vehicle Spd
Vehicle speed / min.: 0
km/h (0 mph), max.:
255 km/h (159 mph)
Actual vehicle speed is
displayed
-
CCS Mem Vehicle Spd Vehicle speed / min.: 0
km/h (0 mph), max.:
255 km/h (159 mph)
Actual vehicle speed
stored in memory
-
for 3UR-FE:
ON: Shift lever
position D (6th,
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Cruise Control - Tundra
Cruise Operation Status
Shift lever position
signal / ON or OFF
5th or 4th gear)
OFF: Shift lever
position except D
(6th, 5th or 4th
gear)
for 1GR-FE,
2UZ-FE:
ON: Shift lever
position D (5th or
4th gear)
OFF: Shift lever
position except D
(5th or 4th gear)
-
Cruise Control
Cruise control / ON or
OFF
ON: Cruise control is
SET
OFF: Cruise control is
UNSET
-
CCS Indicator M-CPU
CRUISE main indicator
light (Main CPU)/ON or
OFF
ON: CRUISE main
indicator light is ON
OFF: CRUISE main
indicator light is OFF
-
CCS Ready M-CPU
Cruise control system
standby condition (Main
CPU) / ON or OFF
ON <----> OFF:
Changes each time main
switch is pushed
-
CCS Main SW M-CPU
Cruise control main
switch (Main CPU) /
ON or OFF
ON: Cruise control
main switch (Main
CPU) is SET
OFF: Cruise control
main switch (Main
CPU) is UNSET
-
Cancel Switch
CANCEL switch / ON
or OFF
ON: CANCEL switch is
SET
OFF: CANCEL switch
is UNSET
-
SET/COAST Switch
-/SET switch / ON or
OFF
ON: -/SET switch is
SET
OFF: -/SET switch is
UNSET
-
RES/ACC Switch
+/RES switch / ON or
OFF
ON: +/RES switch is
SET
OFF: +/RES switch is
UNSET
-
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Cruise Control - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст