Toyota Tundra. Manual — part 2706
a. When the ignition switch is turned OFF, the steering column moves away from the driver, and also
tilts up for easy ingress and egress.
b. When the ignition switch is turned ON, the steering column returns to the previously set position.
c. The auto away/return function can be prohibited by using the Techstream.
4. DRIVING POSITION MEMORY FUNCTION
a. The steering column moves to the previously set position by pressing the seat memory switches.
HOW TO PROCEED WITH TROUBLESHOOTING
HINT:
Use the following procedures to troubleshoot the power tilt and power telescopic steering column system.
*: Use the Techstream.
1. VEHICLE BROUGHT TO WORKSHOP
2. INSPECT BATTERY VOLTAGE
Standard voltage: 11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
3. CHECK CAN COMMUNICATION SYSTEM*
a. Use the Techstream to check if the CAN communication system is functioning normally (see CAN
COMMUNICATION SYSTEM ).
Result
RESULT REFERENCE TABLE
B: Go to CAN COMMUNICATION SYSTEM
A: Go to next step.
4. CHECK FOR DTC*
a. Check for DTCs (see DTC CHECK/CLEAR ).
b. Clear the DTCs (see DTC CHECK/CLEAR ).
c. Recheck the DTCs (see DTC CHECK/CLEAR ).
Result
RESULT REFERENCE
Result
Proceed to
CAN DTC is not output
A
CAN DTC is output
B
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
B: Go to DIAGNOSTIC TROUBLE CODE TABLE
A: Go to next step.
5. PROBLEM SYMPTOMS TABLE
Result
RESULT REFERENCE TABLE
B: Go to step 7.
A: Go to next step.
6. OVERALL ANALYSIS AND TROUBLESHOOTING*
a. See TERMINALS OF ECU .
b. See DATA LIST/ACTIVE TEST ).
7. REPAIR
8. CONFIRMATION TEST
NEXT: END
CUSTOMIZE PARAMETERS
1. CUSTOMIZING FUNCTION WITH TECHSTREAM (REFERENCE)
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the Techstream on.
d. Enter the following menus: Body/Tilt & Telescopic/Utility/Customize Setting.
Result
Proceed to
DTC does not reoccur
A
DTC reoccurs
B
Result
Proceed to
Fault is not listed in problem symptoms table
A
Fault is listed in problem symptoms table
B
NOTE:
When the customer requests a change in a function, first make sure
that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is
set to the default setting.
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
e. Select the setting by referring to the table below.
Tilt & Telescopic
TILT AND TELESCOPIC REFERENCE TABLE
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. The potential causes of the
symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each
symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
The power tilt and power telescopic steering column system uses the CAN communication system, so
check its diagnostic system before proceeding to troubleshooting.
If the problem still occurs when there is no abnormality in the related circuits, check the multiplex tilt and
telescopic ECU and replace it if necessary.
Power tilt and power telescopic steering column system
POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SYMPTOMS CHART
Display
Default
Contents
Setting
Autoaway/Return function
ON
ON/OFF of the auto away/return function ON/OFF
Symptom
Suspected Area
Reference
Tilt and telescopic
function does not operate
at all
Check DTCs
DTC CHECK/CLEAR
Actuator power source circuit
ACTUATOR POWER SOURCE CIRCUIT
IG power source circuit
IG POWER SOURCE CIRCUIT
Manual switch only does
not operate
Tilt and telescopic manual
switch circuit
DTC B2603: TILT AND TELESCOPIC
MANUAL SWITCH CIRCUIT
MALFUNCTION
Headlight dimmer switch
assembly (tilt and telescopic
manual switch)
DTC B2603: TILT AND TELESCOPIC
MANUAL SWITCH CIRCUIT
MALFUNCTION
Auto away/return
function only does not
operate
Check status of auto away
function using the Techstream
CUSTOMIZE PARAMETERS
IG power source circuit
IG POWER SOURCE CIRCUIT
Actuator power source circuit
ACTUATOR POWER SOURCE CIRCUIT
Auto away function only
does not operate
Unlock warning switch
DTC B2602: KEY UNLOCK WARNING
SWITCH CIRCUIT MALFUNCTION
Ignition switch
INSPECTION
Multiplex tilt and telescopic
ECU
TERMINALS OF ECU
Auto return function
Unlock warning switch
DTC B2602: KEY UNLOCK WARNING
SWITCH CIRCUIT MALFUNCTION
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
TERMINALS OF ECU
1. CHECK MULTIPLEX TILT AND TELESCOPIC ECU
Fig. 10: Identifying Terminals Of ECU
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Measure the voltage according to the value(s) in the table below.
CONNECTOR TERMINAL WIRING COLOR REFERENCE TABLE
only does not operate
Ignition switch
INSPECTION
Multiplex tilt and telescopic
ECU
TERMINALS OF ECU
Memory function only
does not operate
Front power seat control ECU
and switch LH
SYSTEM DESCRIPTION
Multiplex tilt and telescopic
ECU
TERMINALS OF ECU
Terminal No.
(Symbols)
Wiring Color
Terminal
Description
Condition
Specified
Condition
A-2 (TEM+) -
J47-11 (GND)
(Not
available) -
W-B
Telescopic motor
output
Ignition switch
ON
Telescopic
steering contracts
11 to 14 V
Telescopic motor is not
operating
Below 1 V
A-3 (VCE) - A-
5 (E2)
(Not
available)
Telescopic sensor
power source
Ignition switch ON
8 to 16 V
A-4 (TES) - A-
5 (E2)
(Not
available)
Telescopic sensor
signal
Telescopic motor is
operating
Pulse generation
High: 8 to 16 V
Low: Below 1 V
A-5 (E2) -
Body ground
(Not
available) -
Body ground
Telescopic sensor
ground
Always
Below 1 V
A-6 (TEM-) -
(Not
Telescopic motor
Ignition switch
ON
11 to 14 V
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст