Toyota Tundra. Manual — part 2321
Standard tip clearance: 0.180 to 0.300 mm (0.00709 to 0.0118 in.)
Maximum tip clearance: 0.300 mm (0.0118 in.)
If the tip clearance is greater than the maximum, replace the timing chain cover sub-
assembly
c
Check the side clearance
Fig. 82: Measuring Clearance Between Rotors And Steel Square
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
1
Using a feeler gauge and steel square, measure the clearance between the rotors and steel
square as shown in the illustration
Standard side clearance: 0.030 to 0.090 mm (0.00118 to 0.00354 in.)
Maximum side clearance: 0.090 mm (0.00354 in.)
If the side clearance is greater than the maximum, replace the timing chain cover sub-
assembly
d
Check the body clearance
Fig. 83: Measuring Clearance Between Timing Chain Cover And Driven Rotor
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
1
Using a feeler gauge, measure the clearance between the timing chain cover and driven rotor
as shown in the illustration
Standard body clearance: 0.175 to 0.250 mm (0.00689 to 0.00984 in.)
Maximum body clearance: 0.250 mm (0.00984 in.)
If the body clearance is greater than the maximum, replace the timing chain cover sub-
assembly
REASSEMBLY
1
INSTALL OIL PUMP RELIEF VALVE
a
Coat the oil pump relief valve with engine oil
b
Install the relief valve and relief valve spring into the oil pump cover hole
c
Install the plug
Torque: 53 N*m (540 kgf*cm, 39 ft.*lbf)
Fig. 84: Identifying Relief Valve Plug
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
INSTALL OIL PUMP COVER
a
Install the driven rotor, drive rotor and oil pump cover with the 13 bolts
Torque: 10 N*m (105 kgf*cm, 8 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Fig. 85: Identifying Oil Pump Cover Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1
INSTALL WATER INLET PIPE
a
Apply soapy water to 2 new O-rings and install them to the inlet pipe
b
Install the inlet pipe to the No 1 heat exchanger cover
Fig. 86: Identifying Water Inlet Pipe O-Ring
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
a
Apply a light coat of engine oil to a new oil pump gasket
Fig. 87: Identifying Oil Pump Gasket At Cylinder Block
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the oil pump gasket
c
Apply a light coat of engine oil to a new O-ring
d
Install the O-ring
Fig. 88: Identifying O-Ring From Oil Pan
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e
Apply seal packing in a continuous line to the timing chain cover as shown in the following
illustration
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст