Toyota Tundra. Manual — part 1070
Fig. 135: Locating Heat Insulator Bracket Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. REMOVE PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY
a. Remove the 2 bolts and heat insulator bracket from the crossmember.
3. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
a. for Front Differential Side:
1. Place matchmarks on the differential and propeller shaft flange.
Fig. 136: Identifying Matchmarks On Differential And Propeller Shaft Flange
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. Remove the 4 nuts, 4 washers and disconnect the propeller shaft from the differential.
b. for Transfer Side:
1. Place matchmarks on the transfer and propeller shaft flanges.
NOTE:
Use a rope to suspend the front edge of the propeller shaft.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
Fig. 137: Identifying Matchmarks On Transfer And Propeller Shaft Flanges
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. Remove the 4 nuts and 4 washers.
c. Remove the propeller shaft from the transfer flange.
DISASSEMBLY
1. REMOVE FRONT PROPELLER SHAFT JOINT SPIDER BEARING SNAP RING
a. Place matchmarks on the flange yoke.
Fig. 138: Identifying Matchmarks On Flange Yoke
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Using a brass bar and hammer, slightly tap in the spider bearing outer races.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
Fig. 139: Tapping Spider Bearing Outer Races
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Using needle-nose pliers, remove the 4 snap rings from the grooves.
2. REMOVE SPIDER BEARING
a. Using SST, push out the bearing from the flange yoke.
SST 09332-25010
HINT:
Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be
difficult to install.
Fig. 140: Removing Spider Bearing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Clamp the spider bearing outer race in a vise and tap off the propeller shaft with a hammer.
HINT:
Remove the bearing on the opposite side using the same procedure.
Fig. 141: Tapping Propeller Shaft
NOTE:
Do not tap the shaft tube.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Install the 2 removed spider bearing outer races to the spider.
d. Using SST, push the bearing out of the flange yoke.
SST 09332-25010
HINT:
Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be
difficult to install.
Fig. 142: Pushing Bearing Of Flange Yoke
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e. Clamp the outer bearing race in a vise and tap off the flange yoke with a hammer.
Fig. 143: Tapping Flange Yoke
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
f. Remove the spider.
HINT:
Remove the bearing on the opposite side using the same procedure.
INSPECTION
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст