Toyota Tundra. Manual — part 490
Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start
voltage.
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs (see DTC CHECK / CLEAR ).
These DTCs do not indicate a malfunction.
DTC 01-E2 ON / OFF INDICATION PARAMETER ERROR
DESCRIPTION
DTC TROUBLE DETECTION CONDITION CHART
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs (see DTC CHECK / CLEAR ).
1. REPLACE NAVIGATION RECEIVER
a. Replace the navigation receiver (for Column Shift Type) (see REMOVAL ).
b. Replace the navigation receiver (for Floor Shift Type) (see REMOVAL ).
NEXT: END
DTC 21-10 PANEL SWITCH ERROR; DTC 21-11 TOUCH SWITCH ERROR; DTC 23-10 PANEL
SWITCH ERROR; DTC 23-11 TOUCH SWITCH ERROR; DTC 24-10 PANEL SWITCH ERROR;
DTC 24-11 TOUCH SWITCH ERROR; DTC 25-10 PANEL SWITCH ERROR; DTC 25-11 TOUCH
SWITCH ERROR
DESCRIPTION
DTC TROUBLE DETECTION CONDITION CHART
DTC No.
DTC Detection Condition
Trouble Area
01-E2
Signal for ON / OFF control from master device has problem.
Navigation receiver
DTC No.
DTC Detection Condition
Trouble Area
21-10
Panel switch detection circuit has a problem.
Navigation receiver
21-11
Touch panel switch has a problem.
23-10
Panel switch detection circuit has a problem.
23-11
Touch panel switch has a problem.
24-10
Panel switch detection circuit has a problem.
24-11
Touch panel switch has a problem.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs (see DTC CHECK / CLEAR ).
1. REPLACE NAVIGATION RECEIVER
a. Replace the navigation receiver (for Column Shift Type) (see REMOVAL ).
b. Replace the navigation receiver (for Floor Shift Type) (see REMOVAL ).
NEXT: END
DTC 34-10 ERROR IN PICTURE CIRCUIT; DTC 34-11 NO CURRENT IN BACK-LIGHT; DTC 34-12
EXCESS CURRENT IN BACK-LIGHT
DESCRIPTION
DTC TROUBLE DETECTION CONDITION CHART
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs (see DTC CHECK / CLEAR ).
1. REPLACE NAVIGATION RECEIVER
a. Replace the navigation receiver (for Column Shift Type) (see REMOVAL ).
b. Replace the navigation receiver (for Floor Shift Type) (see REMOVAL ).
NEXT: END
DTC 57-47 BLUETOOTH MODULE INITIALIZATION FAILED
DESCRIPTION
DTC TROUBLE DETECTION CONDITION CHART
25-10
Panel switch detection circuit has a problem.
25-11
Touch panel switch has a problem.
DTC No.
DTC Detection Condition
Trouble Area
34-10
Error in power supply system for picture circuit.
Navigation receiver
34-11
Decline in power output from inverter circuit for back-light.
34-12
Excess power output from inverter circuit for back-light.
DTC No.
DTC Detection Condition
Trouble Area
When one of following conditions is met:
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs (see DTC CHECK / CLEAR ).
1. REPLACE NAVIGATION RECEIVER
a. Replace the navigation receiver (for Column Shift Type) (see REMOVAL ).
b. Replace the navigation receiver (for Floor Shift Type) (see REMOVAL ).
NEXT: END
DTC 58-10 GYRO ERROR; DTC 80-10 GYRO ERROR
DESCRIPTION
DTC TROUBLE DETECTION CONDITION CHART
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs (see DTC CHECK / CLEAR ).
1. CHECK VEHICLE SENSOR (NAVIGATION CHECK MODE)
a. Enter the "Navigation Check" mode (Vehicle Sensors) (see NAVIGATION CHECK MODE ).
Fig. 95: Diagnostic Menu Screen Display - Navigation Check Mode
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
57-47
"Bluetooth" module is not installed.
Problem with "Bluetooth" module.
Problem in communication line to "Bluetooth" module.
Navigation receiver
DTC No.
DTC Detection Condition
Trouble Area
58-10
Ground short, power supply short, or open circuit in gyro signal.
Gyro sensor
Navigation receiver
80-10
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
b. Check the gyro voltage.
Standard voltage:
0.5 to 4.5 V
Result
GYRO VOLTAGE RESULT CHART
B: REPLACE NAVIGATION RECEIVER (see REMOVAL (For Column Shift Type) )
C: REPLACE NAVIGATION RECEIVER (see REMOVAL (For Floor Shift Type) )
A: Go to next step
2. CLEAR DTC
a. Clear the DTCs (see DTC CHECK / CLEAR ).
3. RECHECK DTC
a. Recheck for DTCs and check if the same trouble occurs again.
HINT:
If DTCs are detected frequently, replace the navigation receiver.
OK: Malfunction disappears.
Result
DTC RESULT CHART
B: REPLACE NAVIGATION RECEIVER (see REMOVAL (For Column Shift Type) )
C: REPLACE NAVIGATION RECEIVER (see REMOVAL (For Floor Shift Type) )
A: END
Result
Proceed to
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
Result
Proceed to
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст