Toyota Tundra. Manual — part 2771
Standard Resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
Fig. 25: Identifying J31 ECU Connector & P17 Receiver Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
5. CHECK TRANSMITTER ID
a. Turn the ignition switch off.
b. Connect the Techstream to the DLC3.
c. Turn the ignition switch to ON and the Techstream on.
d. Enter the following menus: Chassis/Tire Pressure Monitor/Data List.
e. Check the values by referring to the table below.
Tester Connection
Condition Specified Condition
J31-12 (RDA) - P17-1 (RDA)
Always
Below 1 ohms
J31-11 (GND2) - P17-4 (GND) Always
Below 1 ohms
J31-6 (RF5V) - P17-5 (+5V)
Always
Below 1 ohms
J31-12 (RDA) - Body ground
Always
10 kohms or higher
J31-11 (GND2) - Body ground
Always
10 kohms or higher
J31-6 (RF5V) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
Tire Pressure Monitor
TIRE PRESSURE MONITOR TABLE
f. Check the transmitter ID on the identified transmitter by removing it from the tire and wheel.
Fig. 26: Identifying Pressure Warning Valve And Transmitter
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
g. Confirm that the transmitter ID on the transmitter and recorded transmitter ID match.
Result
RESULT TABLE
Tester
Display
Measurement
Item/Display
Normal Condition
Diagnostic Note
Registered
ID1 Code
Registered ID1
code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in
the transmitter ID1 is displayed
*: Displayed only when the
transmitter ID is not
registered.
Registered
ID2 Code
Registered ID2
code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in
the transmitter ID2 is displayed
*: Displayed only when the
transmitter ID is not
registered.
Registered
ID3 Code
Registered ID3
code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in
the transmitter ID3 is displayed
*: Displayed only when the
transmitter ID is not
registered.
Registered
ID4 Code
Registered ID4
code/
min.: 0
max.: FFFFFFFF*
The transmitter ID registered in
the transmitter ID4 is displayed
*: Displayed only when the
transmitter ID is not
registered.
Result
Proceed to
Match
A
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
B: Go to step 7
A: Go to next step
6. REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a. Replace the tire pressure warning valve and transmitter (See REMOVAL ).
7. REGISTRATION OF TRANSMITTER ID
a. Perform REGISTRATION .
8. PERFORM INITIALIZATION
a. Perform INITIALIZATION .
9. CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a. Turn the ignition switch off.
b. Connect the Techstream to the DLC3.
c. Turn the ignition switch to ON and the Techstream on.
d. Enter the following menus: Chassis/Tire Pressure Monitor/Data List.
e. Check the values by referring to the table below.
Tire Pressure Monitor
TIRE PRESSURE MONITOR TABLE
Do not match
B
Tester
Display
Measurement Item/Range
Normal
Condition
Diagnostic Note
ID1 Tire
Inflation
Pressure
ID1 tire inflation pressure /
min.: Absolute pressure/100 kPa
(1 kgf/cm
2
, 14 psi), Relative
pressure/0 kPa (0 kgf/cm
2
, 0 psi)
max.: Absolute pressure/449.35
kPa (4.5 kgf/cm
2
, 63 psi),
Relative pressure/349.35 kPa
(3.6 kgf/cm
2
, 51 psi)
Actual tire
inflation
pressure
If 100 kPa (1 kgf/cm
2
, 14 psi) for the
absolute pressure or 0 kPa (0
kgf/cm
2
, 0 psi) is displayed for the
relative pressure, the data has not
been received.*
ID2 Tire
Inflation
Pressure
ID2 tire inflation pressure /
min.: Absolute pressure/100 kPa
(1 kgf/cm
2
, 14 psi), Relative
pressure/0 kPa (0 kgf/cm
2
, 0 psi)
max.: Absolute pressure/449.35
kPa (4.5 kgf/cm
2
, 63 psi),
Relative pressure/349.35 kPa
(3.6 kgf/cm
2
, 51 psi)
Actual tire
inflation
pressure
If 100 kPa (1 kgf/cm
2
, 14 psi) for the
absolute pressure or 0 kPa (0
kgf/cm
2
, 0 psi) is displayed for the
relative pressure, the data has not
been received.*
ID3 tire inflation pressure /
min.: Absolute pressure/100 kPa
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
Result
RESULT TABLE
B: END
A: Go to next step
10. REPLACE TIRE PRESSURE WARNING ANTENNA AND RECEIVER
a. Replace the tire pressure warning antenna and receiver (See REMOVAL ).
11. CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a. Turn the ignition switch off.
b. Connect the Techstream to the DLC3.
c. Turn the ignition switch to ON and the Techstream on.
d. Enter the following menus: Chassis/Tire Pressure Monitor/Data List.
e. Check the values by referring to the table below.
Tire Pressure Monitor
ID3 Tire
Inflation
Pressure
(1 kgf/cm
2
, 14 psi), Relative
pressure/0 kPa (0 kgf/cm
2
, 0 psi)
max.: Absolute pressure/449.35
kPa (4.5 kgf/cm
2
, 63 psi),
Relative pressure/349.35 kPa
(3.6 kgf/cm
2
, 51 psi)
Actual tire
inflation
pressure
If 100 kPa (1 kgf/cm
2
, 14 psi) for the
absolute pressure or 0 kPa (0
kgf/cm
2
, 0 psi) is displayed for the
relative pressure, the data has not
been received.*
ID4 Tire
Inflation
Pressure
ID4 tire inflation pressure /min.:
Absolute pressure/100 kPa (1
kgf/cm
2
, 14 psi), Relative
pressure /
0 kPa (0 kgf/cm
2
, 0 psi)
max.: Absolute pressure/449.35
kPa (4.5 kgf/cm
2
, 63 psi),
Relative pressure/349.35 kPa
(3.6 kgf/cm
2
, 51 psi)
Actual tire
inflation
pressure
If 100 kPa (1 kgf/cm
2
, 14 psi) for the
absolute pressure or 0 kPa (0
kgf/cm
2
, 0 psi) is displayed for the
relative pressure, the data has not
been received.*
HINT:
*: It may take about 5 to 6 minutes until the values are displayed.
When no "ID Tire Inflation Pressure" has changed, rotate the tire 90 to 270°. Then rapidly
release the tire pressure and recheck it.
Result
Proceed to
Tire pressure values are not displayed.
A
All tire pressure readings are equal to specified values.
B
2009 Toyota Tundra
2009 SUSPENSION Tire & Wheel - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст