Toyota Tundra. Manual — part 2842
Fig. 115: Identifying Shift Solenoid Valve SLU - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a. Disconnect the D63 No. 1 transmission wire connector.
b. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
Tester Connection
Condition Specified Condition
12 (SLU+) - 4 (SLU-)
20°C (68°F)
5.0 to 5.6 ohms
12 (SLU+) - Body ground
Always
10 kohms or higher
4 (SLU-) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Fig. 116: Identifying D63 No. 1 Transmission Wire Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: Go to step 3
OK: Go to next step.
2. CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
a. Disconnect the D74 ECM connector.
b. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
Result
Fig. 117: Identifying D74 ECM Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
D74-10 (SLU+) - D74-11 (SLU-) 20°C (68°F)
5.0 to 5.6 ohms
D74-10 (SLU+) - Body ground
Always
10 kohms or higher
D74-11 (SLU-) - Body ground
Always
10 kohms or higher
Result
Proceed To
NG
A
OK (for 3UR-FE)
B
OK (for 3UR-FBE)
C
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
B: OK (for 3UR-FE) (See REMOVAL )
C: OK (for 3UR-FBE) (See REMOVAL )
3. INSPECT SHIFT SOLENOID VALVE SLU
a. Remove shift solenoid valve SLU.
b. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
c. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to
terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an
operating noise.
OK: Valve moves and makes an operating noise.
Fig. 118: Identifying Shift Solenoid Valve SLU
Tester Connection Condition Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 ohms
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE SHIFT SOLENOID VALVE SLU (See DISASSEMBLY )
OK: REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE (See REMOVAL )
DTC P2772: FOUR WHEEL DRIVE (4WD) LOW SWITCH CIRCUIT RANGE/PERFORMANCE
DESCRIPTION
The ECM detects the signal from the transfer 4L position switch.
This DTC indicates that the transfer 4L position switch remains on.
DTC DETECTION CONDITION TABLE
MONITOR DESCRIPTION
The ECM monitors the transfer-case 4L position switch to determine when the transfer-case 4L gear is engaged.
If the transfer-case 4L gears remain engaged under the following conditions, the ECM will conclude that there
is a malfunction of the 4L position switch, illuminate the MIL and store the DTC:
The 4L switch indicates that the 4L transfer-case gears are engaged.
The transfer-case shifter is in the "4H" position.
The transfer-case output shaft RPM is between 1000 and 3000 RPM.
The specified time period has elapsed.
MONITOR STRATEGY
MONITOR STRATEGY TABLE
DTC
Code
DTC Detection Condition
Trouble Area
P2772
Transfer 4L position switch remains ON while vehicle is running
under following conditions for 1.8 sec. or more (1-trip detection
logic)
a. Output shaft speed between 1000 and 3000 RPM
b. Transfer position switch is in 4H
Short in transfer 4L
position switch circuit
4WD control ECU
ECM
Related DTCs
P2772: Transfer 4L position switch/ON malfunction
Required sensors/Components
Transfer 4L position switch
Frequency of operation
Continuous
Duration
ON malfunction (A): 1.8 sec.
ON malfunction (B): 0.5 sec.
MIL operation
1 driving cycle
Sequence of operation
None
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст