Toyota Tundra. Manual — part 580
CHART
If the power source circuit is operating normally, proceed to the next step.
3. INSPECT NAVIGATION RECEIVER
a. Disconnect the K18 and K8 receiver connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
NAVIGATION RECEIVER TESTER CONNECTION SPECIFIED CONDITION
Fig. 436: Identifying K18 And K8 Receiver Connectors
Component
Proceed to
Navigation receiver (140)
NAVIGATION RECEIVER ASSEMBLY
POWER SOURCE CIRCUIT
Television display (1B0)*
TELEVISION DISPLAY POWER SOURCE
CIRCUIT *
HINT:
*: w/ Rear Seat Entertainment System
Tester Connection
Condition Specified Condition
K18-5 (ATX+) - K18-15 (ATX-)
Always
60 to 80 ohms
K8-9 (TXM+) - K8-10 (TXM-)*
HINT:
*: w/ Rear Seat Entertainment System
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Result
NAVIGATION RECEIVER RESULT CHART
B: REPLACE NAVIGATION RECEIVER (see REMOVAL (For Column Shift Type) )
C: REPLACE NAVIGATION RECEIVER (see REMOVAL (For Floor Shift Type) )
A: Go to Next Step
4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER -
COMPONENT SHOWN BY SUB-CODE)
HINT:
Start the check from the circuit that is near the component shown by the sub-code first.
For details of the connectors, refer to "TERMINALS OF ECU" .
a. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the stereo
component amplifier and the component shown by the sub-code.
1. Disconnect all connectors between the stereo component amplifier and the component shown
by sub-code.
2. Check for an open or short in the AVC-LAN circuit between the stereo component amplifier
and the component shown by the sub-code.
OK: There is no open or short circuit.
Fig. 437: AVC-LAN Wiring Diagram (W/O Rear Seat Entertainment System)
Result
Proceed to
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 438: AVC-LAN Wiring Diagram (W/ Rear Seat Entertainment System)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
5. REPLACE COMPONENT SHOWN BY SUB-CODE
a. Replace the component shown by the sub-code with a normal one and check if the same problem
occurs again.
OK: Same problem does not occur.
NG: REPLACE STEREO COMPONENT AMPLIFIER (See REMOVAL )
OK: END
TELEVISION DISPLAY ASSEMBLY COMMUNICATION ERROR
INSPECTION PROCEDURE
1. IDENTIFY COMPONENT SHOWN BY SUB-CODE
a. Enter the diagnostic mode.
b. Press the "LAN Mon" switch to change to "LAN Monitor" mode.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
c. Identify the component shown by the sub-code.
HINT:
"140 (navigation receiver)" is the component shown by sub-code in the example shown in the
illustration.
The sub-code will be indicated by its physical address.
For the component list, refer to "DIAGNOSIS DISPLAY DETAILED DESCRIPTION" .
Fig. 439: Display - System Check Mode
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. CHECK POWER SOURCE CIRCUIT OF COMPONENT SHOWN BY SUB-CODE
a. Inspect the power source circuit is operating normally, proceed to the next step.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст