Toyota Tundra. Manual — part 9
INITIALIZATION
1. Procedures necessary when battery terminal is disconnected/reconnected
Procedures necessary when battery terminal is disconnected/reconnected
BATTERY TERMINAL DISCONNECTED/RECONNECTED PROCEDURES REFERENCE
2. Procedures necessary when ECU or other parts are replaced
Procedures necessary when ECU or other parts are replaced
ECU OR OTHER PARTS REPLACEMENT DISCONNECTED/RECONNECTED
PROCEDURES REFERENCE
Necessary
Procedures
Procedure Details
Effects/Inoperative Functions
When Necessary Procedures
are not Performed
Notes
Navigation
system
initialization
After turning the
ignition switch on
(IG), insert the map
disc.
Navigation system
If the map disc is inside when
disconnecting the cable from the
battery terminal, this procedure
is not necessary
NOTE:
After the ignition switch is turned OFF, the navigation system requires
approximately 90 seconds to record various types of memory and
settings. As a result, after turning the ignition switch OFF, wait 90 seconds
or more before disconnecting the cable from the negative (-) battery
terminal.
Replacement Part
Necessary
Procedures
Effects/Inoperative Functions
When Necessary Procedures
are not Performed
Notes
ECM
Register VIN
DTC P0630 is output
-
Automatic
transmission
assembly
Engine
assembly
ECM
Reset memory
Large shift shock
-
Tire pressure
warning ECU
1. Register
transmitter IDs
2. Initialize tire
pressure
warning system
When DTC detection
conditions of
"transmitter ID not
received" DTC is met,
tire pressure warning
light blinks for 1 minute,
and then illuminates
Tire pressure monitoring
-
2009 Toyota Tundra
2009 GENERAL INFORMATION Introduction - Tundra
function
Tire pressure
warning valve and
transmitter
1. Register
transmitter IDs
2. Initialize tire
pressure
warning system
When DTC detection
conditions of
"transmitter ID not
received" DTC is met,
tire pressure warning
light blinks for 1 minute,
and then illuminates
Tire pressure monitoring
function of replaced
wheel
Even if only one wheel is
replaced, IDs for all 4
wheels must be registered.
Skid control ECU
Deceleration
sensor zero
point
calibration
Master cylinder
pressure sensor
zero point
calibration
ABS warning light
illumination
VSC OFF indicator light
illumination
-
Yaw rate sensor
Zero point
calibration data
clearance
Deceleration
sensor zero
point
calibration
ABS warning light
illumination
VSC OFF indicator light
illumination
VSC control is
prohibited or operation is
incorrect
-
Front Wheel
Alignment
Adjustment
Zero point
calibration data
clearance
Deceleration
sensor zero
point
calibration
Perform
initialization of
steering angle
sensor
ABS warning light
illumination
VSC OFF indicator light
illumination
Complete the adjustment of
the steering wheel and
wheel alignment, and then
initialize the steering angle
sensor. If the order is
reversed, the steering wheel
and wheel alignment will
become misaligned.
Occupant
classification ECU
Zero point
calibration
Sensitivity
check
Occupant classification
system
Passenger airbag
ON/OFF indicator
Airbag system (Front
passenger side)
-
2009 Toyota Tundra
2009 GENERAL INFORMATION Introduction - Tundra
3. DESCRIPTION
HINT:
This registration section consists of two parts: Read VIN and Write VIN.
a. Read VIN: Explains the VIN reading process in a flowchart. This process allows the VIN stored in
the ECM to be read in order to confirm that the two VINs, provided with the vehicle and stored in
the vehicle's ECM, are the same.
b. Write VIN: Explains the VIN writing process in a flowchart. This process allows the VIN to be
input into the ECM. If the ECM is changed, or the ECM VIN and vehicle VIN do not match, the
VIN can be registered, or overwritten in the ECM by following this procedure.
4. READ VIN
a. Confirm the vehicle VIN.
b. Connect Techstream to the DLC3.
c. Turn the ignition switch ON.
d. Turn the tester ON.
Seat belt warning system
(Front passenger side)
Transponder
key ECU
ECM
Key
Registration
Engine starting
-
Door control
transmitter
Door control
receiver
Register recognition
code
Wireless door lock operation
-
Inner rear view
mirror
Compass zone
setting
Compass
calibration
Register
transmitter code
Direction is not
displayed correctly
Garage door opener
system
-
Sliding roof
driver gear
(Sliding roof
ECU)
Sliding roof
housing
Sliding roof
glass
Initialize sliding roof
system
Auto operation
Jam protection function
Sliding roof operation
after ignition switch is
turned OFF
Key-linked operation
function (Driver side
door only)
-
2009 Toyota Tundra
2009 GENERAL INFORMATION Introduction - Tundra
e. Enter the following menus: Powertrain/Engine and ECT/Utility/VIN/VIN Read.
5. WRITE VIN
a. Confirm the vehicle VIN.
b. Connect Techstream to the DLC3.
c. Turn the ignition switch ON.
d. Turn the tester ON.
e. Enter the following menus: Powertrain/Engine and ECT/Utility/VIN/VIN Write.
6. RESET MEMORY
HINT:
The ECM memorizes the control conditions of the automatic transmission assembly and engine assembly.
Therefore, when the automatic transmission assembly, engine assembly, or ECM has been replaced, it is
necessary to reset the memory so that the ECM can memorize the new information. Reset procedure is as
follows.
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch ON and push the tester switch ON.
c. Enter the following menus:
1. Select: Powertrain/Engine and ECT/Utility/Reset Memory.
HINT:
The ECM learns through the ROAD TEST.
7. DESCRIPTION OF CODE REGISTRATION
It is necessary to register the transmitter ID in the tire pressure warning ECU when replacing the tire
pressure warning valve and transmitter and/or tire pressure warning ECU.
Prepare all transmitter ID data before starting registration.
a. Before registration
1. In case of tire pressure warning ECU replacement:
Read the registered transmitter IDs that are stored in the old ECU using the Techstream
and note them down.
NOTE:
Perform the RESET MEMORY (AT initialization) when replacing the
automatic transmission assembly, engine assembly or ECM.
The RESET MEMORY can be performed only with the Techstream.
NOTE:
After performing the RESET MEMORY, be sure to perform the
ROAD TEST described earlier.
2009 Toyota Tundra
2009 GENERAL INFORMATION Introduction - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст