Toyota Tundra. Manual — part 2649
Fig. 233: Identifying Steering Pad Contact Plates
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. REMOVE LOWER NO. 3 STEERING WHEEL COVER
CAUTION: Wait at least 90 seconds after disconnecting the cable from the
negative (-) battery terminal to prevent airbag and seat belt
pretensioner activation.
NOTE:
After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.
Some systems need to be initialized after the cable is reconnected
(see INITIALIZATION ).
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
a. Using a screwdriver, remove the steering wheel cover.
HINT:
Tape the screwdriver tip before use.
Fig. 234: Identifying Lower No. 3 Steering Wheel Cover Claws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. REMOVE LOWER NO. 2 STEERING WHEEL COVER
a. w/Cruise Control:
1. Using a screwdriver, remove the No. 2 steering wheel cover.
HINT:
Tape the screwdriver tip before use.
Fig. 235: Identifying Lower No. 2 Steering Wheel Cover Claws (W/ Cruise Control)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. w/o Cruise Control:
1. Using a screwdriver, remove the No. 2 steering wheel cover.
HINT:
Tape the screwdriver tip before use.
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
Fig. 236: Identifying Lower No. 2 Steering Wheel Cover Claws (W/O Cruise Control)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4. REMOVE STEERING PAD (w/ Steering Pad Switch)
a. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw
circumference catches on the screw case.
Fig. 237: Locating Steering Pad Screws (W/ Steering Pad Switch)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Pull out the steering pad from the steering wheel, as shown below. Then support the steering pad
with one hand.
c. Disconnect the 2 connectors and remove the steering pad.
NOTE:
When removing the steering pad, do not pull the airbag wire harness.
NOTE:
When handling the airbag connector, take care not to damage the
airbag wire harness.
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
Fig. 238: Locating Steering Pad Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5. REMOVE STEERING PAD (w/o Steering Pad Switch)
a. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw
circumference catches on the screw case.
Fig. 239: Locating Steering Pad Screws (W/O Steering Pad Switch)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Pull out the steering pad from the steering wheel, as shown below. Then support the steering pad
with one hand.
c. Disconnect the 2 connectors and remove the steering pad.
NOTE:
When removing the steering pad, do not pull the airbag wire harness.
NOTE:
When handling the airbag connector, take care not to damage the
airbag wire harness.
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст