Toyota Tundra. Manual — part 1979
22
INSTALL INTAKE MANIFOLD (See INSTALLATION )
23
INSTALL NO. 1 TUBE
a
Install the No 1 tube with the 2 bolts
Torque: 8.2 N*m (83 kgf*cm, 73 in.*lbf)
Fig. 397: Locating No. 1 Tube With Mounting Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
24
CONNECT VENTILATION HOSE ASSEMBLY (See INSTALLATION )
25
INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH (See INSTALLATION )
26
INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH (See INSTALLATION )
27
INSTALL NO. 1 ENGINE MOUNTING BRACKET LH
a
Install the mounting bracket with the 4 bolts
Torque: 35 N*m (357 kgf*cm, 26 ft.*lbf)
Fig. 398: Locating Front No. 1 Engine Mounting Bracket LH Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
28
INSTALL NO. 1 ENGINE MOUNTING BRACKET RH
a
Install the mounting bracket with the 4 bolts
Torque: 35 N*m (357 kgf*cm, 26 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 399: Locating Mounting Bracket With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
29
INSTALL FRONT ENGINE MOUNTING INSULATOR RH (See INSTALLATION )
30
INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
a
Apply adhesive to 2 or 3 threads of the drain cocks
Adhesive:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Fig. 400: Applying Adhesive To 2 Or 3 Threads Of Drain Cocks
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the water drain cocks
Torque: 30 N*m (306 kgf*cm, 22 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 401: Locating Drain Cocks
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Further tighten the drain cocks within 360° so that the drain cock pipes are within the range shown
in the illustration
d
Install the water drain cock plugs to the water drain cocks
Torque: 13 N*m (133 kgf*cm, 10 ft.*lbf)
31
INSTALL FRONT ENGINE MOUNTING INSULATOR LH (See INSTALLATION )
32
INSTALL FUEL TUBE
a
Install the fuel tube (See FUEL SYSTEM )
NOTE:
Do not rotate the drain cocks more than 1 revolution (360°) after
tightening the drain cocks to the specified torque.
Do not loosen the drain cocks to adjust them. If an adjustment
is necessary, remove the drain cocks and reinstall them.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 402: Identifying Fuel Tube
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
33
INSTALL ENGINE WIRE
a
Install the engine wire
b
Engine Rear Side:
1
Install the 3 wires with the 3 bolts
Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf)
2
Connect the 5 clamps
3
Connect the 2 air switching valve connectors
Fig. 403: Locating Engine Wire, Clamps And Air Switching Valve Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Engine RH Side:
1
Connect the 7 clamps
2
Connect the oil pressure sender gauge connector
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст