Toyota Tundra. Manual — part 1976
Fig. 374: Tightening Camshaft Timing Gear Bolt - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
Using a wrench to hold the hexagonal portion of the No 4 camshaft, tighten the camshaft
timing exhaust gear with the bolt
Torque: 100 N*m (1020 kgf*cm, 74 ft.*lbf)
Fig. 375: Tightening Camshaft Timing Exhaust Gear Bolt - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
RH:
1
Using a wrench to hold the hexagonal portion of the No 1 camshaft, tighten the camshaft
timing gear with the bolt
Torque: 100 N*m (1020 kgf*cm, 74 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 376: Tightening Camshaft Timing Gear Bolt - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
Using a wrench to hold the hexagonal portion of the No 2 camshaft, tighten the camshaft
timing exhaust gear with the bolt
Torque: 100 N*m (1020 kgf*cm, 74 ft.*lbf)
Fig. 377: Tightening Camshaft Timing Exhaust Gear Bolt - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
36
CHECK NO. 1 CYLINDER TO TDC/COMPRESSION
a
Temporarily install the pulley set bolt
b
Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing gear and
camshaft timing gears are as shown in the illustration
c
Remove the crankshaft pulley bolt
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 378: Identifying Timing Marks
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
37
INSTALL WATER INLET PIPE (See INSTALLATION )
38
INSTALL WATER PUMP ASSEMBLY (See INSTALLATION )
39
INSTALL TIMING CHAIN COVER SUB-ASSEMBLY (See INSTALLATION )
40
INSTALL FRONT CRANKSHAFT OIL SEAL
a
Apply MP grease to the lip of a new oil seal
b
Using SST and a hammer, tap in the oil seal to a depth between 0 to 1 0 mm (0 to 0 0394 in ) from
the timing chain cover edge
SST 09223-22010,09506-35010
NOTE:
Keep the lip free from foreign matter.
Do not tap oil seal at an angle.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
41
INSTALL CRANKSHAFT TIMING GEAR KEY
a
Install the crankshaft timing gear key to the crankshaft
Fig. 380: Identifying Crankshaft Timing Gear Key
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
42
INSTALL SPARK PLUG TUBE GASKET
a
Using a cutter knife, cut off the seal part of the removed gasket
Fig. 381: Identifying Spark Plug Tube Gasket Cut Off Area
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 379: Installing Front Crankshaft Oil Seal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст