Toyota Tundra. Manual — part 2797
2. PERFORM ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be
operated without removing any parts. This non-intrusive functional inspection can be very useful because
intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests
early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while
performing Active Tests.
a. Warm up the engine.
b. Turn the ignition switch off.
c. Connect the Techstream to the DLC3.
d. Turn the ignition switch to ON.
e. Turn the Techstream on.
f. Enter the following menus: Powertrain/Engine and ECT/Active Test.
g. According to the display on the Techstream, perform the Active Test.
Engine and ECT:
ACTIVE TEST
Not operating: OFF
SLU Solenoid
Status
Shift solenoid SLU
status/ ON or OFF
Shift solenoid SLU is:
Operating: ON
Not operating: OFF
-
SLT Solenoid
Status
Shift solenoid SLT
status/ ON or OFF
Accelerator pedal is
depressed: OFF
Accelerator pedal is
released: ON
-
Tester
Display
Test Part
Control Range
Diagnostic Note
Activate the
Solenoid
(SLU)
Operate shift solenoid
SLU
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
ON or OFF
HINT:
[Vehicle Condition]
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Activate the
Solenoid
(SLT)*
Operate shift solenoid
SLT and raise line
pressure
OFF: Line pressure up (when
Active Test "Activate the
Solenoid (SLT)" is performed,
ECM commands SLT solenoid
to turn OFF)
ON: No action (normal
operation)
Vehicle
stopped
Engine idling
Activate the
Solenoid
(S1)
Operate shift solenoid
S1
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
Activate the
Solenoid
(S2)
Operate shift solenoid
S2
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
Activate the
Solenoid
(S3)
Operate shift solenoid
S3
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
Activate the
Solenoid
(S4)
Operate shift solenoid
S4
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
Activate the
Lock Up
Control shift solenoid
SLU to set automatic
transmission to lock-up
condition
ON or OFF
Possible to check
shift solenoid valve
SLU operation
[Vehicle Condition]
Throttle valve
opening angle:
Less than 35%
Vehicle speed:
60 km/h (37
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
DIAGNOSTIC TROUBLE CODE TABLE
HINT:
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the
reference given.
*1: "Comes on" means the Malfunction Indicator Lamp (MIL) illuminates.
*2: "DTC stored" means the ECM memorizes the malfunction code if the ECM detects the DTC detection
condition.
These DTCs may be output when the clutch, brake, gear components, etc., inside the automatic
transmission are damaged.
MPH) or more
Control the
Shift
Position
Operate shift solenoid
valve and set each shift
position
Press "-->" button: Shift up
Press "<--" button: Shift down
Possible to check
operation of shift
solenoid valves
[Vehicle Condition]
50 km/h (31 MPH)
or less
Activate the
Solenoid
(SR)
Operate shift solenoid
SR
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
Activate the
Solenoid
(SL1)
Operate shift solenoid
SL1
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
Activate the
Solenoid
(SL2)
Operate shift solenoid
SL2
ON or OFF
[Vehicle Condition]
Engine
stopped
Shift lever on
P or N
position
HINT:
*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes
by connecting SST to the automatic transmission, which is used in HYDRAULIC TEST as well.
Note that the pressure values in the Active Test and HYDRAULIC TEST are different.
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Automatic transmission system:
DIAGNOSTIC TROUBLE CODE TABLE
DTC Code
Detection Item
Trouble Area
MIL*1
Memory*2
P0705
Transmission Range
Sensor Circuit
Malfunction (PRNDL
Input)
Open or short in
park/neutral
position switch
circuit
Transmission
control switch
Park/neutral
position switch
ECM
Comes on
DTC stored
P0710
Transmission Fluid
Temperature Sensor "A"
Circuit
Open or short in
No. 1 ATF
temperature sensor
circuit
No. 1 transmission
wire (No. 1 ATF
temperature sensor)
ECM
Comes on
DTC stored
P0711
Transmission Fluid
Temperature Sensor "A"
Performance
No. 1 transmission wire
(No. 1 ATF temperature
sensor)
Comes on
DTC stored
P0712
Transmission Fluid
Temperature Sensor "A"
Circuit Low Input
Short in No. 1 ATF
temperature sensor
circuit
No. 1 transmission
wire (No. 1 ATF
temperature sensor)
ECM
Comes on
DTC stored
P0713
Transmission Fluid
Temperature Sensor "A"
Circuit High Input
Open in No. 1 ATF
temperature sensor
circuit
No. 1 transmission
wire (No. 1 ATF
temperature sensor)
ECM
Comes on
DTC stored
P0717
Turbine Speed Sensor
Circuit No Signal
Open or short in
speed sensor NT
circuit
Speed sensor NT
Comes on
DTC stored
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст