Toyota Tundra. Manual — part 765
HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms
are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking
the suspected areas in the order they are listed. Replace parts as necessary.
Wiper and washer system
WIPER AND WASHER SYSTEM
Other
OTHER
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Symptom
Suspected Area
Refer To
Front wiper and washer system
does not operate
Windshield wiper switch
INSPECTION
Windshield wiper motor
INSPECTION
Harness or connector
-
Front wiper system does not
operate in LO or HI
WIPER fuse
-
Windshield wiper switch
INSPECTION
Windshield wiper motor
INSPECTION
Harness or connector
-
Front wiper system does not
operate in INT
WIPER fuse
-
Windshield wiper switch
INSPECTION
Windshield wiper motor
INSPECTION
Harness or connector
-
Front washer system does not
operate
WSH fuse
-
Windshield wiper switch
INSPECTION
Windshield washer motor and
pump
REMOVAL
Harness or connector
-
Front wiper arms do not return to
their original positions when
wiper switch is turned off
Windshield wiper motor
INSPECTION
Harness or connector
-
Symptom
Suspected Area
Refer To
Washer fluid level warning
system does not operate
Washer fluid level warning switch
circuit
WASHER FLUID LEVEL
WARNING SWITCH CIRCUIT
Meter / gauge system
PROBLEM SYMPTOMS
TABLE
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Wiper & Washer - Tundra
Using the Techstream to read the DATA LIST allows values or status of switches, sensors, actuators and
other items to be read without removing any parts. This non-intrusive inspection can be very useful
because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading
the DATA LIST information early in troubleshooting is one way to save diagnostic time.
a. Warm up the engine.
b. Turn the ignition switch OFF.
c. Connect the Techstream to the DLC3.
d. Turn the ignition switch ON.
e. Turn the tester on.
f. Enter the following menus:
Techstream - Select: Body / Combination Meter / Data List.
g. According to the display on tester, read the "Data List".
Techstream
COMBINATION METER
WASHER FLUID LEVEL WARNING SWITCH CIRCUIT
DESCRIPTION
When the volume of washer fluid decreases below a certain level (when the washer fluid level warning switch is
turned ON), the combination meter warns the driver through the master warning light illumination, and the
warning message on the multi-information display*.
HINT:
*: w/ Multi-information display
WIRING DIAGRAM
NOTE:
In the table below, the values listed under "Normal Condition" are
reference values. Do not depend solely on these reference values when
deciding whether a part is faulty or not.
Tester
Display
Measurement Item/Range
Normal Condition
Diagnostic
Note
Washer
Switch
Washer fluid level warning switch / ON or
OFF
ON: Washer jar is
empty
OFF: Washer jar is full
-
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Wiper & Washer - Tundra
Fig. 4: Washer Fluid Level Warning Switch - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. READ VALUE OF TECHSTREAM (WASHER FLUID LEVEL WARNING SWITCH)
a. Check the DATA LIST for proper functioning of the washer fluid level warning switch.
Techstream
COMBINATION METER
OK: On tester screen, each item changes between ON and OFF according to above chart.
NG: Go to step 2
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
2. CHECK WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY
a. Disconnect the A27 switch connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY
Tester
Display
Measurement Item/Range
Normal Condition
Diagnostic
Note
Washer
Switch
Washer fluid level warning switch / ON or
OFF
ON: Washer jar is
empty
OFF: Washer jar is full
-
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Wiper & Washer - Tundra
Fig. 5: Checking Washer Fluid Level Warning Switch Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE WASHER FLUID LEVEL WARNING SWITCH ASSEMBLY
OK: Go to next step
3. CHECK HARNESS AND CONNECTOR (WASHER FLUID LEVEL WARNING SWITCH
COMBINATION METER)
a. Disconnect the A27 switch connector.
b. Disconnect the J28 meter connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
WASHER FLUID LEVEL WARNING SWITCH COMBINATION METER
Tester Connection
Condition
Specified Condition
A27-1 (S) - A27-2 (E) Washer jar is empty
Below 1 ohms
A27-1 (S) - A27-2 (E) Washer jar is full
10 kohms or higher
Tester Connection
Condition Specified Condition
A27-1 (S) - J28-10 (WLVL) Always
Below 1 ohms
A27-2 (E) - Body ground
Always
Below 1 ohms
A27-1 (S) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Wiper & Washer - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст