Toyota Sequoia (2021 year). Manual in english — part 7
400
SEQUOIA_OM_USA_OM0C035U
NOTICE
■
To prevent paint deterioration and corrosion on the body and compo-
nents (aluminum wheels, etc.)
●
Wash the vehicle immediately in the following cases:
• After driving near the sea coast
• After driving on salted roads
• If coal tar or tree sap is present on the paint surface
• If dead insects, insect droppings or bird droppings are present on the
paint surface
• After driving in an area contaminated with soot, oily smoke, mine dust,
iron powder or chemical substances
• If the vehicle becomes heavily soiled with dust or mud
• If liquids such as benzene and gasoline are spilled on the paint surface
●
If the paint is chipped or scratched, have it repaired immediately.
●
To prevent the wheels from corroding, remove any dirt and store in a place
with low humidity when storing the wheels.
■
Cleaning the exterior lights
●
Wash carefully. Do not use organic substances or scrub with a hard brush.
This may damage the surfaces of the lights.
●
Do not apply wax to the surfaces of the lights.
Wax may cause damage to the lenses.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
401
6-1. Maintenance and care
6
Mainten
SEQUOIA_OM_USA_OM0C035U
NOTICE
■
When using a high pressure car wash
●
Do not spray water directly on the radar which is equipped behind the
emblem. Otherwise it may cause the device to be damaged.
●
Do not bring the nozzle tip close to boots (rubber or resin manufactured
cover), connectors or the following parts. The parts may be damaged if
they come into contact with high-pressure water.
• Traction related parts
• Steering parts
• Suspension parts
• Brake parts
●
Keep the cleaning nozzle at least 11.9 in. (30 cm) away from the vehicle
body. Otherwise resin section, such as moldings and bumpers, may be
deformed and damaged. Also, do not continuously hold the nozzle in the
same place.
●
Do not spray the lower part of the windshield continuously.
If water enters the air conditioning system intake located near the lower
part of the windshield, the air conditioning system may not operate cor-
rectly.
●
Do not wash the underside of the vehicle using a high pressure car
washer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
402
SEQUOIA_OM_USA_OM0C035U
Cleaning and protecting the vehicle interior
●
Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces
with a cloth dampened with lukewarm water.
●
If dirt cannot be removed, wipe it off with a soft cloth dampened with
neutral detergent diluted to approximately 1%.
Wring out any excess water from the cloth and thoroughly wipe off
remaining traces of detergent and water.
●
Remove dirt and dust using a vacuum cleaner.
●
Wipe off any excess dirt and dust with a soft cloth dampened with
diluted detergent.
Use a diluted water solution of approximately 5% neutral wool detergent.
●
Wring out any excess water from the cloth and thoroughly wipe off
all remaining traces of detergent.
●
Wipe the surface with a dry, soft cloth to remove any remaining
moisture. Allow the leather to dry in a shaded and ventilated area.
●
Remove dirt and dust using a vacuum cleaner.
●
Wipe it off with a soft cloth dampened with neutral detergent diluted
to approximately 1%.
●
Wring out any excess water from the cloth and thoroughly wipe off
remaining traces of detergent and water.
The following procedures will help protect your vehicle’s interior
and keep it in top condition:
Protecting the vehicle interior
Cleaning the leather areas
Cleaning the synthetic leather areas
-------------------------------------------------------------------------------------------------------------------------------------------------------------
403
6-1. Maintenance and care
6
Mainten
SEQUOIA_OM_USA_OM0C035U
■
Caring for leather areas
Toyota recommends cleaning the interior of the vehicle at least twice a year to
maintain the quality of the vehicle’s interior.
■
Shampooing the carpets
There are several commercial foaming-type cleaners available. Use a sponge
or brush to apply the foam. Rub in overlapping circles. Do not use water.
Wipe dirty surfaces and let them dry. Excellent results are obtained by keep-
ing the carpet as dry as possible.
■
Seat belts
Clean with mild soap and lukewarm water using a cloth or sponge. Also
check the belts periodically for excessive wear, fraying or cuts.
WARNING
■
Water in the vehicle
●
Do not splash or spill liquid in the vehicle.
Doing so may cause electrical components, etc., to malfunction or catch
fire.
●
Do not get any of the SRS components or wiring in the vehicle interior wet.
(
An electrical malfunction may cause the airbags to deploy or not function
properly, resulting in death or serious injury.
■
Cleaning the interior (especially instrument panel)
Do not use a polish wax or polish cleaner. The instrument panel may reflect
off the windshield, obstructing the driver’s view and leading to an accident,
resulting in death or serious injury.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
404
SEQUOIA_OM_USA_OM0C035U
NOTICE
■
Cleaning detergents
●
Do not use the following types of detergent, as they may discolor the vehi-
cle interior or cause streaks or damage to painted surfaces:
• Non-seat portions: Organic substances such as benzene or gasoline,
alkaline or acidic solutions, dye, and bleach
• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-
hol
●
Do not use a polish wax or polish cleaner. The instrument panel’s or other
interior part’s painted surface may be damaged.
■
Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of
leather surfaces:
●
Remove any dust or dirt from leather surfaces immediately.
●
Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
●
Do not place items made of vinyl, plastic, or containing wax on the uphol-
stery, as they may stick to the leather surface if the vehicle interior heats
up significantly.
■
Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio system may be damaged if water comes
into contact with electrical components such as the audio system above or
under the floor of the vehicle. Water may also cause the body to rust.
■
When cleaning the inside of the windshield
Do not allow glass cleaner to contact the lens. Also, do not touch the lens.
(
■
Cleaning the inside of the rear quarter windows and back window
●
Do not use a glass cleaner to clean the rear quarter windows and back
window, as this may cause damage to the rear window defogger heater
wires or antenna. Use a cloth dampened with lukewarm water to gently
wipe the window clean. Wipe the window in strokes running parallel to the
heater wires or antenna.
●
Be careful not to scratch or damage the heater wires or antenna.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
405
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Maintenance requirements
General maintenance should be performed on a daily basis. This can
be done by yourself or by a Toyota dealer.
Scheduled maintenance should be performed at specified intervals
according to the maintenance schedule.
For details about maintenance items and schedules, refer to the “Sched-
uled Maintenance Guide” or “Owner’s Manual Supplement”.
You can perform some maintenance procedures by yourself.
Please be aware that do-it-yourself maintenance may affect warranty
coverage.
The use of Toyota Repair Manuals is recommended.
For details about warranty coverage, refer to the separate “Owner’s War-
ranty Information Booklet” or “Owner’s Manual Supplement”.
■
Repair and replacement
It is recommended that genuine Toyota parts be used for repairs to ensure
performance of each system. If non-Toyota parts are used in replacement or if
a repair shop other than a Toyota dealer performs repairs, confirm the war-
ranty coverage.
To ensure safe and economical driving, day-to-day care and reg-
ular maintenance are essential. It is the owner’s responsibility to
perform regular checks. Toyota recommends the following main-
tenance:
General maintenance
Scheduled maintenance
Do-it-yourself maintenance
-------------------------------------------------------------------------------------------------------------------------------------------------------------
406
SEQUOIA_OM_USA_OM0C035U
■
Resetting the message indicating maintenance is required
After the required maintenance is performed according to the maintenance
schedule, please reset the reminder light or message.
To reset the reminder light or message, follow the procedure described
below:
Press “<“ or “>” of the meter control switches, select
on the multi infor-
mation display.
Press “
” or “
” of the meter control switches and select “Vehicle Settings”,
and then press
.
Press “
” or “
” of the meter control switches, select “Maintenance Reset”
and then press
.
Select the “Yes” and press
.
■
Allow inspection and repairs to be performed by a Toyota dealer
●
Toyota technicians are well-trained specialists and are kept up to date with
the latest service information. They are well informed about the operations
of all systems on your vehicle.
●
Keep a copy of the repair order. It proves that the maintenance that has
been performed is under warranty coverage. If any problem should arise
while your vehicle is under warranty, your Toyota dealer will promptly take
care of it.
WARNING
■
If your vehicle is not properly maintained
Improper maintenance could result in serious damage to the vehicle and
possible death or serious injury.
■
Handling of the battery
●
Engine exhaust, some of its constituents, and a wide variety of automobile
components contain or emit chemicals known to the State of California to
cause cancer and birth defects and other reproductive harm. Work in a
well ventilated area.
●
Oils, fuels and fluids contained in vehicles as well as waste produced by
component wear contain or emit chemicals known to the State of Califor-
nia to cause cancer and birth defects or other reproductive harm. Avoid
exposure and wash any affected area immediately.
●
Battery posts, terminals and related accessories contain lead and lead
compounds which are known to cause brain damage. Wash your hands
after handling. (
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
407
6
Mainten
SEQUOIA_OM_USA_OM0C035U
General maintenance
Listed below are the general maintenance items that should be
performed at the intervals specified in the “Owner’s Warranty
Information Booklet” or “Owner’s Manual Supplement/Sched-
uled Maintenance Guide”. It is recommended that any problem
you notice should be brought to the attention of your Toyota
dealer or qualified service shop for advice.
Engine compartment
Items
Check points
Battery
Check the connections.
(
Brake fluid
Is the brake fluid at the correct level?
(
Engine coolant
Is the engine coolant at the correct level?(
Engine oil
Is the engine oil at the correct level?
(
Exhaust system
There should not be any fumes or strange sounds.
Power steering fluid
Is the power steering fluid at the correct level?
(
Radiator/condenser
The radiator and condenser should be free from
foreign objects.
(
Washer fluid
Is there sufficient washer fluid?
(
-------------------------------------------------------------------------------------------------------------------------------------------------------------
408
SEQUOIA_OM_USA_OM0C035U
Vehicle interior
Items
Check points
Accelerator pedal
• The accelerator pedal should move smoothly
(without uneven pedal effort or catching).
Automatic transmis-
sion “Park” mecha-
nism
• When parked on a slope and the shift lever is in P,
is the vehicle securely stopped?
Brake pedal
• Does the brake pedal move smoothly?
• Does the brake pedal have appropriate clearance
from the floor?
(
• Does the brake pedal have the correct amount of
free play?
(
Brakes
• The vehicle should not pull to one side when the
brakes are applied.
• The brakes should work effectively.
• The brake pedal should not feel spongy.
• The brake pedal should not get too close to the
floor when the brakes are applied.
Head restraints
• Do the head restraints move smoothly and lock
securely?
Indicators/buzzers
• Do the indicators and buzzers function properly?
Lights
• Do all the lights come on?
Parking brake
• Does the parking brake pedal move smoothly?
• When parked on a slope and the parking brake is
on, is the vehicle securely stopped?
Seat belts
• Do the seat belts operate smoothly?
• The seat belts should not be damaged.
Seats
• Do the seat controls operate properly?
Steering wheel
• Does the steering wheel rotate smoothly?
• Does the steering wheel have the correct amount
of free play?
• There should not be any strange sounds coming
from the steering wheel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
409
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Vehicle exterior
Items
Check points
Doors
• Do the doors operate smoothly?
Engine hood
• Does the engine hood lock system work properly?
Fluid leaks
• There should not be any signs of fluid leakage
after the vehicle has been parked.
Tires
• Is the tire inflation pressure correct?
• The tires should not be damaged or excessively
worn.
• Have the tires been rotated according to the
maintenance schedule?
• The wheel nuts should not be loose.
Windshield wipers/
rear window wiper
• The wiper blades should not show any signs of
cracking, splitting, wear, contamination or defor-
mation.
• The wiper blades should clear the windshield/rear
window without streaking or skipping.
WARNING
■
If the engine is running
Turn the engine off and ensure that there is adequate ventilation before per-
forming maintenance checks.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
410
SEQUOIA_OM_USA_OM0C035U
Emission inspection and maintenance (I/M)
programs
The OBD system determines that a problem exists somewhere in the
emission control system. Your vehicle may not pass the I/M test and
may need to be repaired. Contact your Toyota dealer to service the
vehicle.
●
When the battery is disconnected or discharged
Readiness codes that are set during ordinary driving are erased.
Also, depending on your driving habits, the readiness codes may
not be completely set.
●
When the fuel tank cap is loose
The malfunction indicator lamp comes on indicating a temporary
malfunction and your vehicle may not pass the I/M test.
The error code in the OBD system will not be cleared unless the vehi-
cle is driven 40 or more times.
Contact your Toyota dealer to prepare the vehicle for re-testing.
Some states have vehicle emission inspection programs which
include OBD (On Board Diagnostics) checks. The OBD system
monitors the operation of the emission control system.
If the malfunction indicator lamp comes on
Your vehicle may not pass the I/M test in the following situations:
When the malfunction indicator lamp still remains on after sev-
eral driving trips
If your vehicle does not pass the I/M test
-------------------------------------------------------------------------------------------------------------------------------------------------------------
411
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Do-it-yourself service precautions
If you perform maintenance by yourself, be sure to follow the
correct procedure as given in these sections.
Items
Parts and tools
Battery condition
(
• Warm water
• Baking soda
• Grease
• Conventional wrench (for terminal clamp bolts)
Brake fluid level
(
• FMVSS No.116 DOT 3 or SAE J1703 brake fluid
• Rag or paper towel
• Funnel (used only for adding brake fluid)
Engine coolant
level (
• “Toyota Super Long Life Coolant” or a similar high
quality ethylene glycol-based non-silicate, non-
amine, non-nitrite and non-borate coolant with long-
life hybrid organic acid technology
For the U.S.A.:
“Toyota Super Long Life Coolant” is pre-mixed with
50% coolant and 50 % deionized water.
For Canada:
“Toyota Super Long Life Coolant” is pre-mixed with
55 % coolant and 45 % deionized water.
• Funnel (used only for adding coolant)
Engine oil level
(
• “Toyota Genuine Motor Oil” or equivalent
• Rag or paper towel
• Funnel (used only for adding engine oil)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
412
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Items
Parts and tools
Fuses (
• Fuse with same amperage rating as original
Light bulbs
(
• Bulb with same number and wattage rating as origi-
nal
• Phillips-head screwdriver
• Flathead screwdriver
• Wrench
Power steering
fluid level
(
• Automatic transmission fluid DEXRON
®
II or III
• Rag or paper towel
• Funnel (used only for adding power steering fluid)
Radiator and
condenser
(
Tire inflation
pressure
(
• Tire pressure gauge
• Compressed air source
Washer fluid
(
• Water or washer fluid containing antifreeze (for win-
ter use)
• Funnel (used only for adding water or washer fluid)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
413
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
WARNING
The engine compartment contains many mechanisms and fluids that may
move suddenly, become hot, or become electrically energized. To avoid death
or serious injury, observe the following precautions.
■
When working on the engine compartment
●
Keep hands, clothing and tools away from the moving fan and engine
drive belt.
●
Be careful not to touch the engine, radiator, exhaust manifold, etc. right
after driving as they may be hot. Oil and other fluids may also be hot.
●
Do not leave anything that may burn easily, such as paper and rags, in the
engine compartment.
●
Do not smoke, cause sparks or expose an open flame to fuel or the bat-
tery. Fuel and battery fumes are flammable.
●
Be extremely cautious when working on the battery. It contains poisonous
and corrosive sulfuric acid.
■
When working near the electric cooling fan or radiator grille
Be sure the engine switch is off. With the engine switch on, the electric cool-
ing fans may automatically start to run if the air conditioning is on and/or the
coolant temperature is high. (
■
Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc.
from getting in your eyes.
NOTICE
■
If you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine wear
due to dirt in the air.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
414
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Hood
Pull the hood lock release lever.
The hood will pop up slightly.
Pull up the hood catch lever
and lift the hood.
Release the lock from the inside of the vehicle to open the hood.
1
2
WARNING
■
Pre-driving check
Check that the hood is fully closed and locked.
If the hood is not locked properly, it may open while the vehicle is in motion
and cause an accident, which may result in death or serious injury.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
415
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Engine compartment
Washer fluid tank (
Engine oil level dipstick
(
Engine coolant reservoir
(
Engine oil filler cap (
Brake fluid reservoir
(
Fuse box
(
Battery
(
Radiator
(
Cooling fans
Condenser
(
Power steering fluid reservoir
(
-------------------------------------------------------------------------------------------------------------------------------------------------------------
416
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
With the engine at operating temperature and turned off, check the oil
level on the dipstick.
■
Checking the engine oil
Park the vehicle on level ground. After warming up the engine
and turning it off, wait more than 5 minutes for the oil to drain
back into the bottom of the engine.
Holding a rag under the end,
pull the dipstick out.
Wipe the dipstick clean.
Reinsert the dipstick fully.
Holding a rag under the end,
pull the dipstick out and
check the oil level.
Low
Normal
Excessive
The shape of the dipstick may
differ depending on the type of
vehicle or engine.
Wipe the dipstick and reinsert it fully.
Engine oil
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
417
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
■
Adding engine oil
If the oil level is below or near
the low level mark, add engine
oil of the same type as that
already in the engine.
Make sure to check the oil type and prepare the items needed
before adding oil.
Remove the oil filler cap by turning it counterclockwise.
Add engine oil slowly, checking the dipstick.
Install the oil filler cap by turning it clockwise.
■
Engine oil consumption
A certain amount of engine oil will be consumed while driving. In the following
situations, oil consumption may increase, and engine oil may need to be
refilled in between oil maintenance intervals.
●
When the engine is new, for example directly after purchasing the vehicle or
after replacing the engine
●
If low quality oil or oil of an inappropriate viscosity is used
●
When driving at high engine speeds or with a heavy load, when towing, or
when driving while accelerating or decelerating frequently
●
When leaving the engine idling for a long time, or when driving frequently
through heavy traffic
Engine oil selection
Oil quantity
(Low
Full)
1.6 qt. (1.5 L, 1.3 Imp.qt.)
Items
Clean funnel
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
418
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
WARNING
■
Used engine oil
●
Used engine oil contains potentially harmful contaminants which may
cause skin disorders such as inflammation and skin cancer, so care
should be taken to avoid prolonged and repeated contact. To remove used
engine oil from your skin, wash thoroughly with soap and water.
●
Dispose of used oil and filters only in a safe and acceptable manner. Do
not dispose of used oil and filters in household trash, in sewers or onto the
ground.
Call your Toyota dealer, service station or auto parts store for information
concerning recycling or disposal.
●
Do not leave used engine oil within the reach of children.
NOTICE
■
To prevent serious engine damage
Check the oil level on a regular basis.
■
When replacing the engine oil
●
Be careful not to spill engine oil on the vehicle components.
●
Avoid overfilling, or the engine could be damaged.
●
Check the oil level on the dipstick every time you refill the vehicle.
●
Be sure the engine oil filler cap is properly tightened.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
419
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
The coolant level is satisfactory if it is between the “FULL” and “LOW”
lines on the reservoir when the engine is cold.
Reservoir cap
“FULL” line
“LOW” line
If the level is on or below the
“LOW” line, add coolant up to the
“FULL” line.
■
Coolant selection
Only use “Toyota Super Long Life Coolant” or a similar high quality ethylene
glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with
long-life hybrid organic acid technology.
U.S.A.:
“Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion-
ized water. (Minimum temperature: -31 °F [-35 °C])
Canada:
“Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deion-
ized water. (Minimum temperature: -44 °F [-42 °C])
For more details about engine coolant, contact your Toyota dealer.
■
If the coolant level drops within a short time of replenishing
Visually check the radiator, hoses, engine coolant reservoir caps, drain cock
and water pump.
If you cannot find a leak, have your Toyota dealer test the cap and check for
leaks in the cooling system.
Engine coolant
-------------------------------------------------------------------------------------------------------------------------------------------------------------
420
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Check the radiator and condenser and clear away any foreign objects.
If either of the above parts is extremely dirty or you are not sure of
their condition, have your vehicle inspected by your Toyota dealer.
WARNING
■
When the engine is hot
Do not remove the engine coolant reservoir cap or the radiator cap.
(
The cooling system may be under pressure and may spray hot coolant if the
cap is removed, causing serious injuries, such as burns.
NOTICE
■
When adding coolant
Coolant is neither plain water nor straight antifreeze. The correct mixture of
water and antifreeze must be used to provide proper lubrication, corrosion
protection and cooling. Be sure to read the antifreeze or coolant label.
■
If you spill coolant
Be sure to wash it off with water to prevent it from damaging parts or paint.
Radiator and condenser
WARNING
■
When the engine is hot
Do not touch the radiator or condenser as they may be hot and cause seri-
ous injuries, such as burns.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
421
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
■
Checking fluid level
The brake fluid level should be
between the “MAX” and “MIN”
lines on the reservoir.
■
Adding fluid
Make sure to check the fluid type and prepare the necessary item.
■
Brake fluid can absorb moisture from the air
Excess moisture in the brake fluid can cause a dangerous loss of braking effi-
ciency. Use only newly opened brake fluid.
Brake fluid
Fluid type
FMVSS No.116 DOT 3 or SAE J1703 brake fluid
Items
Clean funnel
WARNING
■
When filling the reservoir
Take care as brake fluid can harm your hands and eyes and damage
painted surfaces.
If fluid gets on your hands or in your eyes, flush the affected area with clean
water immediately.
If you still experience discomfort, see a doctor.
NOTICE
■
If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads
wear out or when the fluid level in the accumulator is high.
If the reservoir needs frequent refilling, there may be a serious problem.
■
If you spill fluid
Be sure to wash it off with water to prevent damage to parts or paint.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
422
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
Fluid level
The fluid level should be within the appropriate range.
Full (when cold)
Add fluid (when cold)
Full (when hot)
Add fluid (when hot)
Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 min-
utes, or slightly longer in frigid temperatures. (Fluid tempera-
ture, 140 °F - 175 °F [60 °C - 80 °C]).
Cold: Engine has not been run for about 5 hours. (Room tempera-
ture, 50 °F - 85 °F [10 °C - 30 °C]).
■
Checking the fluid level
Make sure to check the fluid type and prepare the necessary items.
Clean all dirt off the reservoir.
Remove the cap by turning it counterclockwise.
Wipe the dipstick clean.
Reinstall the cap and remove it again.
Check the fluid level.
Power steering fluid
Fluid type
Automatic transmission fluid DEXRON
®
II or III
Items
Rag or paper, clean funnel (only for adding fluid)
1
2
3
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
423
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Check the battery as follows.
■
Battery exterior
Make sure that the battery terminals are not corroded and that
there are no loose connections, cracks, or loose clamps.
Terminals
Hold-down clamp
■
Before recharging
When recharging, the battery produces hydrogen gas which is flammable and
explosive. Therefore, observe the following before recharging:
●
If recharging with the battery installed on the vehicle, be sure to disconnect
the ground cable.
●
Make sure the power switch on the charger is off when connecting and dis-
connecting the charger cables to the battery.
WARNING
■
When checking the reservoir
Take care as the reservoir may be hot.
NOTICE
■
When adding fluid
Avoid overfilling, or the power steering may be damaged.
■
After replacing the reservoir cap
Check the steering box case, vane pump and hose connections for leaks or
damage.
Battery
-------------------------------------------------------------------------------------------------------------------------------------------------------------
424
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
WARNING
■
Chemicals in the battery
Batteries contain poisonous and corrosive sulfuric acid and may produce
hydrogen gas which is flammable and explosive. To reduce the risk of death
or serious injury, take the following precautions while working on or near the
battery:
●
Do not cause sparks by touching the battery terminals with tools.
●
Do not smoke or light a match near the battery.
●
Avoid contact with eyes, skin and clothes.
●
Never inhale or swallow electrolyte.
●
Wear protective safety glasses when working near the battery.
●
Keep children away from the battery.
■
Where to safely charge the battery
Always charge the battery in an open area. Do not charge the battery in a
garage or closed room where there is insufficient ventilation.
■
How to recharge the battery
Only perform a slow charge (5 A or less). The battery may explode if
charged at a quicker rate.
■
Emergency measures regarding electrolyte
●
If electrolyte gets in your eyes
Flush your eyes with clean water for at least 15 minutes and get immedi-
ate medical attention. If possible, continue to apply water with a sponge or
cloth while traveling to the nearest medical facility.
●
If electrolyte gets on your skin
Wash the affected area thoroughly. If you feel pain or burning, get medical
attention immediately.
●
If electrolyte gets on your clothes
It can soak through clothing on to your skin. Immediately take off the cloth-
ing and follow the procedure above if necessary.
●
If you accidentally swallow electrolyte
Drink a large quantity of water or milk. Get emergency medical attention
immediately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
425
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Add washer fluid in the following
situations:
●
A washer does not work.
●
The warning message appears
on the multi-information display.
NOTICE
■
When recharging the battery
Never recharge the battery while the engine is running. Also, be sure all
accessories are turned off.
Washer fluid
WARNING
■
When adding washer fluid
Do not add washer fluid when the engine is hot or running as washer fluid
contains alcohol and may catch fire if spilled on the engine, etc.
NOTICE
■
Do not use any fluid other than washer fluid
Do not use soapy water or engine antifreeze instead of washer fluid.
Doing so may cause streaking on the vehicle’s painted surfaces, as well as
damaging the pump leading to problems of the washer fluid not spraying.
■
Diluting washer fluid
Dilute washer fluid with water as necessary.
Refer to the freezing temperatures listed on the label of the washer fluid bot-
tle.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
426
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Tires
Check if the treadwear indicators are showing on the tires. Also check
the tires for uneven wear, such as excessive wear on one side of the
tread.
Check the spare tire condition and pressure if not rotated.
New tread
Worn tread
Treadwear indicator
The location of treadwear indicators is shown by a “TWI” or “
” mark,
etc., molded into the sidewall of each tire.
Replace the tires if the treadwear indicators are showing on a tire.
Replace or rotate tires in accordance with maintenance sched-
ules and treadwear.
Checking tires
-------------------------------------------------------------------------------------------------------------------------------------------------------------
427
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Rotate the tires in the order
shown.
To equalize tire wear and extend
tire life, Toyota recommends that
tire rotation is carried out at the
same interval as tire inspection.
Do not fail to initialize the tire
pressure warning system after
tire rotation.
Your vehicle is equipped with a tire pressure warning system that uses
tire pressure warning valves and transmitters to detect low tire infla-
tion pressure before serious problems arise.
●
The tire pressure detected by the tire pressure warning system can
be displayed on the multi-information display.
●
If the tire pressure drops below
a predetermined level, the
driver is warned by a screen
display and a warning light.
The
illustration
used
is
intended as an example, and
may differ from the image that
is actually displayed on the
multi-information display.
◆
Installing tire pressure warning valves and transmitters
When replacing tires or wheels, tire pressure warning valves and
transmitters must also be installed.
When new tire pressure warning valves and transmitters are
installed, new ID codes must be registered in the tire pressure
warning computer and the tire pressure warning system must be
initialized.
Tire rotation
Front
Tire pressure warning system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
428
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
◆
Initializing the tire pressure warning system
■
The tire pressure warning system must be initialized in the fol-
lowing circumstances:
●
When rotating the tires.
●
When the tire inflation pressure is changed such as when chang-
ing tire size. (When there are multiple specified pressures)
●
After registering the ID codes. (
When the tire pressure warning system is initialized, the current tire
inflation pressure is set as the benchmark pressure.
■
How to initialize the tire pressure warning system
Park the vehicle in safe place and turn the engine switch off.
Initialization cannot be performed while the vehicle is moving.
Adjust the tire inflation pressure to the specified cold tire inflation
pressure level. (
Make sure to adjust the tire pressure to the specified cold tire infla-
tion pressure level. The tire pressure warning system will operate
based on this pressure level.
Turn the engine switch to ON.
Push and hold the tire pres-
sure warning reset switch
until the tire pressure warn-
ing light blinks 3 times.
A message is displayed on the
multi-information display. Also,
“- -” is displayed for inflation
pressure of each tire on the
multi-information display while
the tire pressure warning sys-
tem determines the position.
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
429
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Drive straight (with occasional left and right turns) at approxi-
mately 25 mph (40 km/h) or more for approximately 10 to 30 min-
utes.
Initialization is complete when the position of each tire is determined
and the inflation pressure of each tire is displayed on the multi-infor-
mation display.
Initialization may take longer than approximately 30 minutes in cer-
tain situations, such as when the vehicle is stopped for a long time at
traffic lights, etc. (
◆
Registering ID codes
Every tire pressure warning valve and transmitter has a unique ID
code. When replacing a tire pressure warning valve and transmitter,
it is necessary to register the ID codes.
To register the ID codes, perform the following procedure:
Press the tire pressure warn-
ing reset switch 3 times until
the tire pressure warning
light blinks slowly 3 times.
Then a message will be dis-
played on multi-information
display.
When registration is being per-
formed, the tire pressure warn-
ing
light
will
blink
for
approximately 1 minute then
illuminate and “- -” will be dis-
played for the inflation pres-
sure of each tire on the multi-
information display.
5
1
-------------------------------------------------------------------------------------------------------------------------------------------------------------
430
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Drive straight (with occasional left and right turns) at approxi-
mately 25 mph (40 km/h) or more for approximately 10 to 30 min-
utes.
Registration is complete when the tire pressure warning light
turns off and the inflation pressure of each tire is displayed on the
multi-information display.
Registration may take longer than approximately 30 minutes in
certain situations, such as when the vehicle is stopped for a long
time at traffic lights, etc. (
After registering the ID codes, make sure to initialize the tire
pressure warning system. (
■
When to replace your vehicle’s tires
Tires should be replaced if:
●
The treadwear indicators are showing on a tire.
●
You have tire damage such as cuts, splits, cracks deep enough to
expose the fabric, and bulges indicating internal damage
●
A tire goes flat repeatedly or cannot be properly repaired due to the size
or location of a cut or other damage
If you are not sure, consult with your Toyota dealer.
■
When replacing the tires and wheels
If the ID code of the tire pressure warning valve and transmitter is not reg-
istered, the tire pressure warning system will not work properly. After driv-
ing for about 20 minutes, the tire pressure warning light blinks for 1
minute and stays on to indicate a system malfunction.
■
Tire life
Any tire over 6 years old must be checked by a qualified technician even
if it has seldom or never been used, or damage is not obvious.
■
Routine tire inflation pressure checks
The tire pressure warning system does not replace routine tire inflation
pressure checks. Make sure to check tire inflation pressure as part of
your routine of daily vehicle checks.
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
431
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
■
Maximum load of tire
Check that the number given by dividing the maximum load by 1.10 of the
replacement tire is greater than 1/2 of the Gross Axle Weight Ratings
(GAWR) of either the front axle or the rear axle, whichever is greater.
■
Tire types
●
Summer tires
Summer tires are high-speed performance tires best suited to highway
driving under dry conditions. Since summer tires do not have the same
traction performance as snow tires, summer tires are inadequate for
driving on snow-covered or icy roads. For driving on snow-covered
roads or icy roads, the use of snow tires is recommended. When install-
ing snow tires, be sure to replace all four tires.
●
All season tires
All season tires are designed to provide better traction in snow and to
be adequate for driving in most winter conditions as well as for use
year-round. All season tires, however, do not have adequate traction
performance compared with snow tires in heavy or loose snow. Also, all
season tires fall short in acceleration and handling performance com-
pared with summer tires in highway driving.
●
Snow tires
For driving on snow-covered roads or icy roads, we recommend using
snow tires. If you need snow tires, select tires of the same size, con-
struction and load capacity as the originally installed tires. Since your
vehicle has radial tires as original equipment, make sure your snow
tires also have radial construction. Do not install studded tires without
first checking local regulations for possible restrictions. Snow tires
should be installed on all wheels. (
For the GAWR, see the Certification
Label. For the maximum load of the tire,
see the load limit at maximum cold tire
inflation pressure mentioned on the
sidewall of the tire. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
432
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
Initializing the tire pressure warning system
Initialize the system with the tire inflation pressure adjusted to the speci-
fied level.
■
If the tread on snow tires wears down below 0.16 in. (4 mm)
The effectiveness of the tires as snow tires is lost.
■
Situations in which the tire pressure warning system may not oper-
ate properly
●
In the following cases, the tire pressure warning system may not operate
properly.
• If non-genuine Toyota wheels are used.
• A tire has been replaced with a tire that is not an OE (Original Equip-
ment) tire.
• A tire has been replaced with a tire that is not of the specified size.
• Tire chains, etc., are equipped.
• An auxiliary-supported run-flat tire is equipped.
• If a window tint that affects the radio wave signals is installed.
• If there is a lot of snow or ice on the vehicle, particularly around the
wheels or wheel housings.
• If the tire inflation pressure is extremely higher than the specified
level.
• If wheel without the tire pressure warning valve and transmitter is
used.
• If the ID code on the tire pressure warning valves and transmitters is
not registered in the tire pressure warning computer.
●
Performance may be affected in the following situations.
• Near a TV tower, electric power plant, gas station, radio station, large
display, airport or other facility that generates strong radio waves or
electrical noise
• When carrying a portable radio, cellular phone, cordless phone or
other wireless communication device
If tire position information is not correctly displayed due to the radio
wave conditions, the display may be corrected by driving and changing
the radio wave conditions.
●
When the vehicle is parked, the time taken for the warning to start or go
off could be extended.
●
When tire inflation pressure declines rapidly for example when a tire has
burst, the warning may not function.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
433
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
■
The initialization operation
●
Make sure to carry out initialization after adjusting the tire inflation pres-
sure.
Also, make sure the tires are cold before carrying out initialization or tire
inflation pressure adjustment.
●
If you have accidentally turned the engine switch to OFF during initial-
ization, it is not necessary to press the reset switch again as initialization
will restart automatically when the engine switch has been turned to ON
for the next time.
●
If you accidentally press the reset switch when initialization is not neces-
sary, adjust the tire inflation pressure to the specified level when the
tires are cold, and conduct initialization again.
●
While the position of each tire is being determined and the inflation pres-
sures are not being displayed on the multi-information display, if the
inflation pressure of a tire drops, the tire pressure warning light will come
on.
■
Warning performance of the tire pressure warning system
The warning of the tire pressure warning system will change in accor-
dance with the conditions under which it was initialized. For this reason,
the system may give a warning even if the tire pressure does not reach a
low enough level, or if the pressure is higher than the pressure that was
adjusted to when the system was initialized.
■
When initialization of the tire pressure warning system has failed
Initialization may take longer to complete if the vehicle is driven on an
unpaved road. When performing initialization, drive on a paved road if
possible. Depending on the driving environment and condition of the tires,
initialization will be completed in approximately 10 to 30 minutes. If initial-
ization is not complete after driving approximately 10 to 30 minutes, con-
tinue driving for a while.
If the inflation pressure of each tire is not displayed after driving for
approximately 1 hour, perform the following procedure.
●
Park the vehicle in a safe place for approximately 20 minutes. Then
drive straight (with occasional left and right turns) at approximately
25 mph (40 km/h) or more for approximately 10 to 30 minutes.
However, in the following situations, the tire inflation pressure will not be
recorded and the system will not operate properly. Perform initialization
again.
●
When operating the tire pressure warning reset switch, the tire pressure
warning light does not blink 3 times.
●
After performing initialization, the tire pressure warning light blinks for
1 minute then stays on while driving about 20 minutes.
If the inflation pressure of each tire is still not displayed, have the vehicle
inspected by your Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
434
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
Tire pressure warning system certification
For vehicles sold in the U.S.A.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
435
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
For vehicles sold in Canada
Model: PMV-E000
-------------------------------------------------------------------------------------------------------------------------------------------------------------
436
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
WARNING
■
When inspecting or replacing tires
Observe the following precautions to prevent accidents.
Failure to do so may cause damage to parts of the drive train as well as
dangerous handling characteristics, which may lead to an accident
resulting in death or serious injury.
●
Do not mix tires of different makes, models or tread patterns.
Also, do not mix tires of remarkably different treadwear.
●
Do not use tire sizes other than those recommended by Toyota.
●
Do not mix differently constructed tires (radial, bias-belted or bias-ply
tires).
●
Do not mix summer, all season and snow tires.
●
Do not use tires that have been used on another vehicle.
Do not use tires if you do not know how they were used previously.
■
When initializing the tire pressure warning system
Do not initialize tire pressure warning system without first adjusting the
tire inflation pressure to the specified level. Otherwise, the tire pressure
warning light may not come on even if the tire inflation pressure is low,
or it may come on when the tire inflation pressure is actually normal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
437
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
NOTICE
■
Repairing or replacing tires, wheels, tire pressure warning valves,
transmitters and tire valve caps
●
When removing or fitting the wheels, tires or the tire pressure warning
valves and transmitters, contact your Toyota dealer as the tire pres-
sure warning valves and transmitters may be damaged if not handled
correctly.
●
Make sure to install the tire valve caps. If the tire valve caps are not
installed, water could enter the tire pressure warning valves and the
tire pressure warning valves could be bound.
●
When replacing tire valve caps, do not use tire valve caps other than
those specified. The cap may become stuck.
■
To avoid damage to the tire pressure warning valves and transmit-
ters
When a tire is repaired with liquid sealants, the tire pressure warning
valve and transmitter may not operate properly. If a liquid sealant is
used, contact your Toyota dealer or other qualified service shop as soon
as possible. Make sure to replace the tire pressure warning valve and
transmitter when replacing the tire. (
■
Driving on rough roads
Take particular care when driving on roads with loose surfaces or pot-
holes.
These conditions may cause losses in tire inflation pressure, reducing
the cushioning ability of the tires. In addition, driving on rough roads
may cause damage to the tires themselves, as well as the vehicle’s
wheels and body.
■
If tire inflation pressure of each tire becomes low while driving
Do not continue driving, or your tires and/or wheels may be ruined.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
438
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Tire inflation pressure
The recommended cold tire infla-
tion pressure and tire size are dis-
played on the tire and loading
information label. (
Tire inflation pressure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
439
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Tire valve
Tire pressure gauge
Remove the tire valve cap.
Press the tip of the tire pressure gauge onto the tire valve.
Read the pressure using the gauge gradations.
If the tire inflation pressure is not at the recommended level, adjust
the pressure.
If you add too much air, press the center of the valve to deflate.
After completing the tire inflation pressure measurement and
adjustment, apply soapy water to the valve and check for leakage.
Put the tire valve cap back on.
■
Tire inflation pressure check interval
You should check tire inflation pressure every two weeks, or at least once
a month.
Do not forget to check the spare.
■
Effects of incorrect tire inflation pressure
Driving with incorrect tire inflation pressure may result in the following:
●
Reduced fuel economy
●
Reduced driving comfort and poor handling
●
Reduced tire life due to wear
●
Reduced safety
●
Damage to the drive train
If a tire needs frequent inflating, have it checked by your Toyota dealer.
Inspection and adjustment procedure
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
440
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following:
●
Check only when the tires are cold.
If your vehicle has been parked for at least 3 hours or has not been
driven for more than 1 mile or 1.5 km, you will get an accurate cold tire
inflation pressure reading.
●
Always use a tire pressure gauge.
It is difficult to judge if a tire is properly inflated based only on its appear-
ance.
●
It is normal for the tire inflation pressure to be higher after driving as
heat is generated in the tire. Do not reduce tire inflation pressure after
driving.
●
Passengers and luggage weight should be placed so that the vehicle is
balanced.
WARNING
■
Proper inflation is critical to save tire performance
Keep your tires properly inflated.
If the tires are not properly inflated, the following conditions may occur
which could lead to an accident resulting in death or serious injury:
●
Excessive wear
●
Uneven wear
●
Poor handling
●
Possibility of blowouts resulting from overheated tires
●
Air leaking from between tire and wheel
●
Wheel deformation and/or tire damage
●
Greater possibility of tire damage while driving (due to road hazards,
expansion joints, sharp edges in the road, etc.)
NOTICE
■
When inspecting and adjusting tire inflation pressure
Be sure to put the tire valve caps back on.
If a valve cap is not installed, dirt or moisture may get into the valve and
cause an air leak, resulting in decreased tire inflation pressure.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
441
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Wheels
When replacing wheels, care should be taken to ensure that they are
equivalent to those removed in load capacity, diameter, rim width and
inset
*
.
Replacement wheels are available at your Toyota dealer.
*
: Conventionally referred to as “offset”.
Toyota does not recommend using the following:
●
Wheels of different sizes or types
●
Used wheels
●
Bent wheels that have been straightened
●
Use only Toyota wheel nuts and wrenches designed for use with
your aluminum wheels.
●
When rotating, repairing or changing your tires, check that the
wheel nuts are still tight after driving 1000 miles (1600 km).
●
Be careful not to damage the aluminum wheels when using tire
chains.
●
Use only Toyota genuine balance weights or equivalent and a plas-
tic or rubber hammer when balancing your wheels.
If a wheel is bent, cracked or heavily corroded, it should be
replaced. Otherwise, the tire may separate from the wheel or
cause a loss of handling control.
Wheel selection
Aluminum wheel precautions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
442
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
When replacing wheels
The wheels of your vehicle are equipped with tire pressure warning
valves and transmitters that allow the tire pressure warning system to
provide advance warning in the event of a loss in tire inflation pressure.
Whenever wheels are replaced, tire pressure warning valves and trans-
mitters must be installed. (
WARNING
■
When replacing wheels
●
Do not use wheels that are a different size from those recommended in
the Owner’s Manual, as this may result in a loss of handling control.
●
Never use an inner tube in a leaking wheel which is designed for a
tubeless tire. Doing so may result in an accident, causing death or seri-
ous injury.
■
When installing the wheel nuts
●
Be sure to install the wheel nuts with the tapered ends facing inward.
(
P. 499) Installing the nuts with the tapered ends facing outward can
cause the wheel to break and eventually cause the wheel to come off
while driving, which could lead to an accident resulting in death or seri-
ous injury.
●
Never use oil or grease on the wheel bolts or wheel nuts.
Oil and grease may cause the wheel nuts to be excessively tightened,
leading to bolt or disc wheel damage. In addition, the oil or grease can
cause the wheel nuts to loosen and the wheel may fall off, causing an
accident and resulting in death or serious injury. Remove any oil or
grease from the wheel bolts or wheel nuts.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
443
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
NOTICE
■
Replacing tire pressure warning valves and transmitters
●
Because tire repair or replacement may affect the tire pressure warn-
ing valves and transmitters, make sure to have tires serviced by your
Toyota dealer or other qualified service shop. In addition, make sure to
purchase your tire pressure warning valves and transmitters at your
Toyota dealer.
●
Ensure that only genuine Toyota wheels are used on your vehicle.
Tire pressure warning valves and transmitters may not work properly
with non-genuine wheels.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
444
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Air conditioning filter
Turn the engine switch to OFF.
Open the glove box.
Remove the internal tray.
Remove the inside cover by
sliding up while pulling toward
you.
The air conditioning filter must be changed regularly to maintain
air conditioning efficiency.
Removal method
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
445
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Remove the filter cover.
Remove the air conditioning fil-
ter and replace it with a new
one.
The “
UP” marks shown on the fil-
ter should be pointing up.
■
Checking interval
Inspect and replace the air conditioning filter according to the maintenance
schedule. In dusty areas or areas with heavy traffic flow, early replacement
may be required. (For scheduled maintenance information, please refer to the
“Schedule maintenance guide” or “Owner’s Manual Supplement”.)
■
If air flow from the vents decreases dramatically
The filter may be clogged. Check the filter and replace if necessary.
5
6
NOTICE
■
When using the air conditioning system
Make sure that a filter is always installed.
Using the air conditioning system without a filter may cause damage to the
system.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
446
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Electronic key battery
●
Flathead screwdriver
●
Small flathead screwdriver
●
Lithium battery CR2032
Take out the mechanical key.
Remove the module.
To prevent damage to the key,
cover the tip of the screwdriver with
a rag.
Remove the depleted battery.
Insert a new battery with the “+”
terminal facing up.
Replace the battery with a new one if it is depleted.
You will need the following items:
Replacing the battery
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
447
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
■
Use a CR2032 lithium battery
●
Batteries can be purchased at your Toyota dealer, local electrical appliance
shops or camera stores.
●
Replace only with the same or equivalent type recommended by the manu-
facturer.
●
Dispose of used batteries according to local laws.
■
If the electronic key battery is depleted
The following symptoms may occur:
●
The smart key system and wireless remote control will not function properly.
●
The operational range will be reduced.
WARNING
■
Removed battery and other parts
These parts are small and if swallowed by a child, they can cause choking.
Keep away from children. Failure to do so could result in death or serious
injury.
NOTICE
■
For normal operation after replacing the battery
Observe the following precautions to prevent accidents:
●
Always work with dry hands.
Moisture may cause the battery to rust.
●
Do not touch or move any other component inside the remote control.
●
Do not bend either of the battery terminals.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
448
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
Checking and replacing fuses
Turn the engine switch to OFF.
Open the fuse box cover.
Engine compartment
Push the tab in and lift the lid
off.
Under the instrument panel
Remove the lid.
Remove the fuse with the pull-
out tool.
Only type A fuse can be removed
using the pullout tool.
If any of the electrical components do not operate, a fuse may
have blown. If this happens, check and replace the fuses as nec-
essary.
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
449
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Check if the fuse is blown.
Normal fuse
Blown fuse
Type A, B:
Replace the blown fuse with a new fuse of an appropriate amperage rat-
ing. The amperage rating can be found on the fuse box lid.
Type C:
Contact your Toyota dealer.
4
Type A
Type B
Type C
-------------------------------------------------------------------------------------------------------------------------------------------------------------
450
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
After a fuse is replaced
●
If the lights do not turn on even after the fuse has been replaced, a bulb may
need replacement. (
●
If the replaced fuse blows again, have the vehicle inspected by your Toyota
dealer.
■
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
■
When replacing light bulbs
Toyota recommends that you use genuine Toyota products designed for this
vehicle. Because certain bulbs are connected to circuits designed to prevent
overload, non-genuine parts or parts not designed for this vehicle may be
unusable.
WARNING
■
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.
●
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
●
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
●
Do not modify the fuses or fuse boxes.
NOTICE
■
Before replacing fuses
Have the cause of electrical overload determined and repaired by your
Toyota dealer as soon as possible.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
451
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Light bulbs
Check the wattage of the light bulb to be replaced. (
■
Rear
You may replace the following bulbs by yourself. The difficulty
level of replacement varies depending on the bulb. If necessary
bulb replacement seems difficult to perform, contact your
Toyota dealer.
For more information about replacing other light bulbs, contact
your Toyota dealer.
Preparing for light bulb replacement
Bulb locations
Stop/tail and rear side marker
lights
Rear turn signal lights
Back-up lights
Tail lights
License plate light
-------------------------------------------------------------------------------------------------------------------------------------------------------------
452
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
Stop/tail, rear side marker lights and rear turn signal lights
Open the back door and remove the cover.
To protect the cover, place a rag between the flathead screwdriver or
equivalent and cover as shown in the illustrations.
Left side (vehicles without speaker in the luggage)
Replacing light bulbs
1
Right side
Left
side
(vehicles
with
speaker in the luggage)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
453
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Turn the bulb bases counter-
clockwise.
Stop/tail and rear side
marker light
Rear turn signal light
Remove the light bulb.
Stop/tail and rear side
marker light
Rear turn signal light
When installing, reverse the steps listed.
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
454
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
Tail lights, back-up lights
Vehicles with power back
door only: Remove the cov-
ers.
To protect the cover, place a rag
between the flathead screw-
driver or equivalent and cover
as shown in the illustrations.
Remove the nuts.
Remove the rear combina-
tion light assembly in the
order shown in the illustra-
tion.
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
455
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
Turn the bulb base counter-
clockwise.
Tail light
Back-up light
Remove the light bulb.
Tail light
Back-up light
When installing, reverse the steps listed.
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
456
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
■
License plate lights
Remove the screws and
lens.
Remove the light bulb.
When installing, reverse the steps listed.
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
457
6-3. Do-it-yourself maintenance
6
Mainten
SEQUOIA_OM_USA_OM0C035U
■
Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by
your Toyota dealer.
●
Headlight low beams
●
Headlight high beams
●
Front side marker lights
●
Daytime running lights
●
Parking lights
●
Front turn signal lights
●
Front fog lights
●
Side turn signal lights (if equipped)
●
High mounted stoplight
●
Outer foot lights (if equipped)
■
LED light bulbs
The following lights consist of a number of LEDs. If any LEDs burn out, take
your vehicle to your Toyota dealer to have the light replaced.
●
Headlight low beams
●
Headlight high beams
●
Front side marker lights
●
Daytime running lights
●
Parking lights
●
Front turn signal lights
●
Front fog lights
●
Side turn signal lights (if equipped)
●
High mounted stoplight
●
Outer foot lights (if equipped)
■
Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the lens does not indicate a
malfunction. Contact your Toyota dealer for more information in the following
situations:
●
Large drops of water have built up on the inside of the lens.
●
Water has built up inside the lens.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
458
6-3. Do-it-yourself maintenance
SEQUOIA_OM_USA_OM0C035U
WARNING
■
Replacing light bulbs
●
Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
●
Do not touch the glass portion of the light bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth
to avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
●
Do not attempt to repair or disassemble light bulbs, connectors, electric
circuits or component parts.
Doing so may result in death or serious injury due to electric shock.
■
To prevent damage or fire
●
Make sure bulbs are fully seated and locked.
●
Check the wattage of the bulb before installing to prevent heat damage.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
459
When trouble arises
7
SEQUOIA_OM_USA_OM0C035U
Emergency flashers . . .. 460
If your vehicle has to be
stopped in an
emergency . . . . . .. 461
If the vehicle is trapped
in rising water. . . . .. 463
or a warning buzzer
sounds . . . . . . . 470
If you have a flat tire. . .. 491
If the engine will not
If the electronic key does
not operate properly. . 507
-------------------------------------------------------------------------------------------------------------------------------------------------------------
460
SEQUOIA_OM_USA_OM0C035U
Emergency flashers
Press the switch.
All the turn signals will flash.
To turn them off, press the switch
once again.
■
Emergency flashers
●
If the emergency flashers are used for a long time while the engine is not
operating, the battery may discharge.
●
If any of the SRS airbags deploy (inflate) or in the event of a strong rear
impact, the emergency flashers will turn on automatically
The emergency flashers will turn off automatically after operating for approx-
imately 20 minutes. To manually turn the emergency flashers off, press the
switch twice. (The emergency flashers may not turn on automatically
depending on the force of the impact and conditions of the collision.)
The emergency flashers are used to warn other drivers when the
vehicle has to be stopped in the road due to a breakdown, etc.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
461
SEQUOIA_OM_USA_OM0C035U
7
Wh
en tro
If your vehicle has to be stopped in an
emergency
Steadily step on the brake pedal with both feet and firmly depress it.
Do not pump the brake pedal repeatedly as this will increase the effort
required to slow the vehicle.
Shift the shift lever to N.
If the shift lever is shifted to N
After slowing down, stop the vehicle in a safe place by the road.
Stop the engine.
If the shift lever cannot be shifted to N
Keep depressing the brake pedal with both feet to reduce vehicle
speed as much as possible.
To stop the engine, press and
hold the engine switch for 2
consecutive seconds or more,
or press it briefly 3 times or
more in succession.
Stop the vehicle in a safe place by the road.
Only in an emergency, such as if it becomes impossible to stop
the vehicle in the normal way, stop the vehicle using the follow-
ing procedure:
1
2
3
4
3
Press and hold for 2 seconds or more
or press briefly 3 times or more
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
462
SEQUOIA_OM_USA_OM0C035U
WARNING
■
If the engine has to be turned off while driving
Power assist for the brakes and steering wheel will be lost, making the
brake pedal harder to depress and the steering wheel heavier to turn.
Decelerate as much as possible before turning off the engine.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
463
SEQUOIA_OM_USA_OM0C035U
7
Wh
en tro
If the vehicle is trapped in rising water
●
Remove the seat belt first.
●
If the door can be opened, open the door and exit the vehicle.
●
If the door can not be opened, open the window using the power
window switch and exit the vehicle through the window.
●
If the window can not be opened using the power window switch,
remain calm, wait until the water level inside the vehicle rises to the
point that the water pressure inside of the vehicle equals the water
pressure outside of the vehicle, and then open the door and exit the
vehicle.
In the event the vehicle is submerged in water, remain calm and
perform the following.
WARNING
■
Using an emergency hammer
*
for emergency escape
The front side windows and rear side windows, as well as the rear window
can be shattered with an emergency hammer
*
used for emergency escape.
However, an emergency hammer can not shatter the windshield as it is lam-
inated glass.
*
: Contact your Toyota dealer or aftermarket accessory manufacturer for
further information about an emergency hammer.
■
Escaping the vehicle from the window
There are cases where escaping the vehicle from the window is not possi-
ble due to seating position, passenger body type, etc.
When using an emergency hammer, consider your seat location and the
size of the window opening to ensure that the opening is accessible and
large enough to escape.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст