Toyota Prius Plug-in Hybrid (2017 year). Instruction — part 10
2-2. Charging
153
When using the Mode
3
charging cable (if equipped):
Remove the cap of the charging
connector that is connected to
the charging equipment, and
then connect the charging con-
nector to the charging equip-
ment.
Follow the instructions displayed on the charging equipment for details
2
regarding how to connect the charging cable and how to start charging.
Depending on the charging device, it may be necessary to receive authori-
zation to use the device. For details, refer to the information displayed on
the charging device.
3
Open the charging port lid.
Charging inlet light
(P. 114)
The charging inlet light will illumi-
nate.
Remove the charging inlet cap
4
and secure it as shown in the
illustration.
PRIUS PHV_OM_OM47A89E_(EE)
154
2-2. Charging
5
Remove the protective cap of
the charging connector and
secure it to the cable.
The illustration uses a Mode
2
charging cable as an example.
Firmly insert the charging con-
6
nector into the charging inlet.
When the charging connector is
inserted straight as far as possible,
it will automatically lock.
Check that the charging indicator
illuminates. If the charging indica-
tor does not illuminate, the
charging connector is not locked.*
If the charging connector is not
locked, remove and reinsert it.
After the charging connector is locked, even if someone not carrying an
electronic key presses the charging connector lock switch, they cannot
unlock the charging connector.
*: If the charging connector is not firmly inserted, locking operation will be
performed several times.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
155
If the charging indicator flashes
after inserting the charging con-
nector:
The charge schedule is regis-
tered (P. 163). Carry an elec-
tronic key and press the
charging connector lock switch
to unlock the charging connec-
tor.
2
After temporarily removing the charging connector, reinsert it within
approximately 5 seconds. (P. 155)
If the error warning indicator on the CCID (Charging Circuit Interrupting
Device) flashes during charging, check P. 121 and follow the correction
procedure.
The charging indicator will turn off when charging is completed.
■ During charging
● The surface of the CCID (Charging Circuit Interrupting Device) may become
hot, but this does not indicate a malfunction. (When using Mode 2 charging
cable.)
● Depending on radio wave conditions, interference may be heard on the
radio.
● The current charging condition and the estimated time until charging will
complete can be checked on the multi-information display. (P. 146)
● During charging, the hybrid battery (traction battery) status indicator illumi-
nates and flashes, and changes according to the charging amount.
(P. 115)
■ If the charging indicator flashes after connecting the charging cable
The charge schedule (P. 163) is registered and charging cannot be per-
formed immediately. To cancel charging using the timer and start charging
immediately, perform any of the following procedures.
● Turn “Charge Now” on (P. 171)
● While the charging indicator is flashing, remove and reconnect the charging
connector within 5 seconds
■ When the charging connector cannot be inserted into the charging inlet
P. 133
PRIUS PHV_OM_OM47A89E_(EE)
156
2-2. Charging
After charging
Carry an electronic key and
1
press the charging connector
lock switch to unlock the
charging connector.
The charging connector is
unlocked by the smart lid & con-
nector locking system.
If
the charging connector is
unlocked during charging
(while
the charging indicator is on),
charging will be interrupted.
Carrying an electronic key and moving near the charging inlet will cause
the charging inlet light to illuminate.
2
Pull the charging connector
towards you.
3
Attach the charging connector
cap.
Attach the charging inlet cap
4
and close the charging port lid.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
157
5
Only when using the Mode 3
charging cable (if equipped):
After removing the charging
connector from the charging
device, install the cap to the
charging connector.
6
Only when using the Mode 2
2
charging cable:
Remove the plug from the
socket when the charging
equipment will not be used for a
prolonged period of time.
Hold the body of the plug when
removing.
Make sure to put the cable away immediately after disconnecting.
(P. 161)
When leaving the plug inserted, inspect the plug and connector once a
month to check if dirt or dust has accumulated.
PRIUS PHV_OM_OM47A89E_(EE)
158
2-2. Charging
■ Charging time
P. 140
■Safety function
Charging will not start when the charging connector is not locked. If the
charging indicator does not illuminate even when the charging connector is
inserted, remove and reinsert the connector, and then check that the charging
indicator illuminates.
■ When the outside temperature is low or high
The level shown on the remaining charge display (P. 227) may drop slightly
when the power switch is turned to ON mode, even if charging has been com-
pleted and the hybrid battery (traction battery) is fully charged. However, this
does not indicate a malfunction.
■ Charging time may increase
P. 141
■ While charging
When the power switch is turned to ON mode and the energy monitor dis-
plays, the charging connector is displayed on the energy monitor and the flow
of electricity during charging is displayed (P. 218). Also, when the charging
connector is locked,
is displayed.
■ When removing the charging connector
Carry an electronic key and press the
charging connector lock switch and check
that the lock is released, and then pull the
charging connector towards you.
■ Push lifter
When the charging port lid is open, make
sure not to touch the push lifter. If it is
touched accidentally, the charging port lid
or connector lock may operate.
If they are accidentally operated, carry an
electronic key or unlock the doors, and
then press the charging connector lock
Push lifter
switch to unlock.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
159
WARNING
■ When charging
Observe the following precautions.
Failure to do so may cause an unexpected accident, resulting in death or
serious injury.
●Connect to a power source suitable for charging. (P. 136)
●Check that the charging inlet, charging cable, plug and socket are free of
foreign matter.
●Only use sockets where the plug can be securely inserted.
2
●Do not charge if the charging cable is coiled or bundled.
● Wrapping the charging cable while in-use is not recommended because
cable may overheat. Failure to rewrap charging cable when not in-use
could result in strangulation or tripping hazard.
●Do not wash the vehicle while the charging cable is connected to the vehi-
cle and when the charging lid is open.
●Do not touch the terminals of the charging connector and charging inlet
with a sharp metal objects (needles etc.) or hands, or short them with for-
eign objects.
● When charging outdoors, make sure to connect to a rain-tight socket for
outdoor use.
●Do not insert the plug if the socket is submerged in water or snow.
●Follow these points when charging while it is raining or snowing.
• Check that no snow, water or ice has accumulated around the charging
connector terminals and the vehicle charging inlet. Tap snow, water or
ice gently from connector prior to inserting charging connector into the
vehicle’s charging inlet.
• Do not connect the plug if your hands are wet. Also, do not get the plug
or socket wet.
●Do not charge the vehicle during a lightning storm.
●Do not let the wheels on the charging cable, plug, charging connector and
CCID (Charging Circuit Interrupting Device).
●Firmly insert the plug into the socket.
●Do not use an extension cord and converting adaptor.
PRIUS PHV_OM_OM47A89E_(EE)
160
2-2. Charging
WARNING
■ If the error warning indicator on the CCID (Charging Circuit Interrupt-
ing Device) illuminates or flashes during charging
There may be an electrical leakage in the power source path, or there may
be a malfunction in the charging cable or CCID (Charging Circuit Interrupt-
ing Device). Refer to P. 121 and follow the correction procedure. If the error
warning indicator does not turn off even after performing the correction pro-
cedure, immediately stop charging, remove the charging cable and contact
any authorized Toyota dealer or repairer, or another duly qualified and
equipped professional. Continuing to charge the vehicle in that condition
may lead to unforeseen accidents or serious injury.
■ After charging
Remove the plug if it will not be used for a long time.
Dirt and dust may accumulate plug or socket, which could cause a malfunc-
tion or fire, possibly leading to death or serious injury.
■ Charging equipment
There is charging equipment under the rear seats. Make sure to observe
the following precautions regarding the charging equipment. Failure to
observe these precautions may result in death or serious injury such as
burns and electric shocks.
●The charging equipment is hot during charging. Do not touch the charging
equipment, as doing so may result in burns.
●Do not disassemble, repair or modify the charging equipment.
When the charging equipment needs to be repaired, consult any autho-
rized Toyota dealer or repairer, or another duly qualified and equipped pro-
fessional.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
161
NOTICE
■ When use the charging cable and related parts
To prevent damage to the charging cable and related parts, observe the fol-
lowing precautions.
● When interrupting or canceling charging, remove the charging connector
before removing the plug.
● When removing the charging cable, check that the charging connector is
unlocked.
●Do not forcefully pull the connector cap and charging inlet cap.
2
●Do not apply a vibration to the charging connector while charging.
Charging may be stopped.
●Do not insert anything but the charging connector.
● When inserting the plug into or removing the plug from the socket, make
sure to hold the body of the plug.
●Do not damage the charging inlet cap with a sharp object.
●Do not forcefully pull the charging cable that is caught or entangled.
If the cable is entangled, disentangle it before using.
● When charging from the external device, use the charging cable equipped
with the vehicle.
■ When charging
Do not insert the plug into the charging inlet.
The charging inlet may be damaged.
■ After charging
● After disconnecting the charging connector from the charging inlet, make
sure to put on the charging inlet cap and close the charging port lid.
If the charging inlet cap is not put on, water or foreign objects may enter
the charging inlet, which could lead to vehicle damage. (If the charging
port lid is not locked, take care as it may open if unintentionally touched.)
● After removing the plug from the socket, keep it in a safe place free from
moisture and dust.
The charging cable or plug may be damaged if the cable is stepped on or
ridden over by the vehicle.
PRIUS PHV_OM_OM47A89E_(EE)
162
2-2. Charging
NOTICE
■ Using private power generator
Do not use private power generators as a power source for charging.
Doing so may make charging unstable, the voltage may be insufficient, and
the error warning indicator on the CCID
(Charging Circuit Interrupting
Device) of the charging cable may flash.
■ Usable temperature range
●Do not charge if the outside temperature is -30C (-22F) or below, as it is
likely that charging will take longer, and equipment related to charging will
be damaged.
●Do not leave the vehicle or the charging cable in areas where the outside
temperature is lower than -40C (-40F). The vehicle or charging cable will
probably be damaged.
■ Charging equipment
Due to the environment in which the power equipment is located, charging
may be unstable due to noise, the voltage may be insufficient, and the error
warning indicator on the CCID (Charging Circuit Interrupting Device) of the
charging cable may flash.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
163
Using the charging timer function
Charging can be carried out at the desired time by registering
the charge schedule. Also, it is possible to set the timer to one’s
preferences, such as having charging complete by a certain
departure time or be carried out at the same time on certain
days.
2
Settings of the charging timer function
When registering the charge schedule, the following settings can be
changed.
■ Select the charging mode
One of the two following charging modes can be selected.
Charging mode
Operation description
Starts charging at the set time and finishes charging
“Start”
when fully charged.*
Starts charging to finish at the set time.
“Departure”
When this setting is selected, the air conditioning-
linked function can be used. (if equipped)
*: There might be a slight error in the timing when charging starts due to the
state of the hybrid battery (traction battery).
■ Repeated setting
The periodic timer charging can be set by selecting your desired
day of the week.
■ Air conditioning-linked setting (“Climate Prep”) (if equipped)
When the charging mode is set to “Departure”, the vehicle air condi-
tioning system (P. 504) can be set to automatically operate*
according to the set time.
By adjusting the cabin temperature in advance, passengers can enjoy a
pleasant interior immediately after entering the vehicle.
*: Operation starts approximately 10 minutes before the set departure time.
PRIUS PHV_OM_OM47A89E_(EE)
164
2-2. Charging
■ Turning “Charge Now” on and off
If even one charge schedule is registered, charging does not start
until the set time, even if the charging cable is connected to the
vehicle. To start charging immediately without changing the charge
schedule setting, turn “Charge Now” on to temporarily cancel the
charge schedule and enable charging immediate after connecting
the charging cable.
■ Changing “Next Charging Event”*1
It is possible to temporarily set the time of the next scheduled
charge without changing the registered repeated setting.*2
*1: The “Next Charging Event” refers to the closest charge schedule from the
current time among the registered charge schedules. Timer charging is
performed based on the “Next Charging Event”.
*2: When “Next Charging Event” is changed, the current charge schedule will
be temporarily ignored and charging will not be carried out until the time
specified by “Next Charging Event”. (For example, when “Next Charging
Event” is set for 2 days later, even if items are registered on the charge
schedule, charging will not be carried out until the time specified by “Next
Charging Event”.)
■ Timer settings
A maximum of 15 charge schedules can be registered.
■ To make sure that the charging timer function operates correctly
Check the following items.
● Adjust the clock to the correct time (P. 196)
● Check that the power switch is turned off
● After registering the charge schedule, connect the charging cable
The charging start time is determined based on the charge schedule at the
time that the charging cable was connected.
● After connecting the charging cable, check that the charging indicator
flashes (P. 117)
● Do not use a socket that has a power cut off function (including a timer func-
tion)
Use a socket that constantly supplies electricity. For sockets where the
power is cut off due to a timer function, etc., charging may not be carried
out according to plan if the power is cut off during the set time.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
165
■ When the charging cable remains connected to the vehicle
Even if multiple consecutive charge schedules are registered, the next
charge will not be carried out according to the timer until the charging cable is
removed and reconnected after charging completes. Also, when the hybrid
battery (traction battery) is fully charged, charging according to the timer will
not be carried out.
■“Climate Prep” (if equipped)
● When the air conditioning-linked setting is turned on, the air conditioning
operates until the set departure time. Therefore, the air conditioning will con-
sume electricity and charging may not complete by the set departure time.
2
● If the hybrid battery (traction battery) is fully charged, charging will not be
carried out, even if the charge schedule is set. However, if “Climate Prep” is
turned on, the air conditioning will operate only once when it nears the time
set in “Departure”. If this occurs, the air conditioning will consume electricity
and the remaining charge of the hybrid battery (traction battery) when
departing may be decreased.
■ When timer settings are ignored
When the following operations are performed while the charging timer is on
standby, timer charging is temporarily canceled and charging is started imme-
diately.
● When the Remote Air Conditioning System (P. 516) is operated
● When turning “Charge Now” on (P. 171)
● When an operation that temporarily cancel charging using the timer
(P. 155)
■ Effects of outside temperature
When the charging mode is set to “Departure”, timer settings may be ignored
due to the outside temperature and charging may start immediately.
■“Traction Battery Cooler” (if equipped) (P. 142)
When charging is carried out using the timer, the hybrid battery (traction bat-
tery) cooling function may operate according to the temperature of the hybrid
battery (traction battery).
● When the charging mode is set to “Start”, cooling starts at the set charging
start time.
● When the charging mode is set to “Departure”, cooling starts approximately
30 minutes before the charging start time. However, if there is no time to fin-
ish charging by the timer setting, the hybrid battery (traction battery) cooling
time may be shortened and “Traction Battery Cooler” may not operate.
PRIUS PHV_OM_OM47A89E_(EE)
166
2-2. Charging
Setting procedure
When operating timer settings, use the charging timer switch and
meter control switches.
1
Charging timer switch
2
Meter control switches
(P. 191)
Multi-information display
3
■ Registering the charge schedule
Press the charging timer switch.
1
The “Charge Schedule” screen will display on the multi-information dis-
play.
2
Press
or
of the
meter control switches to
select
“Scheduled Events”,
and then press
The “Scheduled Events” screen
will display.
3
Press
or
of the
meter control switches to
select
“+”, and then press
The
“Edit Charging Event”
screen will display.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
167
4
Press
or
of the
meter control switches to
select the charging mode/
time settings row, and then
press
The charging mode/time set-
tings screen will display.
The clock display (12-hour dis-
play/24-hour display) changes
2
according to the clock settings.
(P. 196)
5
Press
or
of the
meter control switches to
select the item to change
with the cursor, and then
press
or
to change
the setting.
Set the desired charging mode
and charging start (or departure)
time.
When the charging mode is “Start”, this sets the charging start time.
When it is “Departure”, this sets the charging end time.
After changing the settings to the desired settings, press
to return to
the previous screen.
6
To activate the repeated set-
ting, press
or
of the
meter control switches to
select
“Repeat”, and then
press
A screen where the repeated
day can be selected will display.
PRIUS PHV_OM_OM47A89E_(EE)
168
2-2. Charging
7
Press
or
of the
meter control switches to
select the desired day to acti-
vate for the repeated setting,
and then press
Each time
is pressed, the
repeated
setting
switches
between on and off.
When set to on, the selected day is highlighted and the charging timer is
repeated on that day. It is possible to set more than one day to on.
If no days are set to on, charging is only carried out once according to
the timer for the next 24 hours.
After changing the settings to the desired settings, press
to return to
the previous screen.
8
When the charging mode is
set to
“Departure”, set the
“Climate Prep” (P. 163) to
on or off. (if equipped)
To turn the function on and oper-
ate the air conditioning, press
or
of the meter control
switches to select
“Climate
Prep”, and then press
Each time
is pressed, the function switches between on and off.
9
After setting operations are
complete, press
A screen where the settings can
be saved will display.
Press
or
of the meter
control switches to select “Yes”,
and then press
to save the
settings.
If you wish to change the settings, select “No” and perform the setting
procedure from step
3
again.
After setting operations are complete, when the charging cable is con-
nected to the vehicle, charging will be carried out according to the
charging timer settings.
PRIUS PHV_OM_OM47A89E_(EE)
2-2. Charging
169
■ Changing the registered charge schedules
The registered charge schedules can be turned on, off, deleted or
modified.
Press the charging timer switch.
1
The “Charge Schedule” screen will display on the multi-information dis-
play.
2
Press
or
of the
meter control switches to
select
“Scheduled Events”,
2
and then press
The “Scheduled Events” screen
is displayed, which displays a
list of the registered charge
schedule.
3
Press
or
of the
meter control switches to
select the item to change,
and then press
The
“Edit Charging Event”
screen will display.
4
Press
or
of the
meter control switches to
select the item to operate
and perform the necessary
operation.
PRIUS PHV_OM_OM47A89E_(EE)
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст